Toyota 85330-60190
Washer Pump

Start the installation of the windshield washer motor and pump assembly by placing it on the washer jar packing. Position the windshield washer jar assembly on its packing then fasten the 5 bolts with 5.5 Nm (56 kgf-cm, 49 in-lbf). After tightening the bolts, complete the installation with 2 connector connections and 3 harness clamp attachments. Wash fluid installation involves connecting the washer hose to the washer motor and pump so that the washer jar receives its liquid contents. The last step involves installing the front bumper cover as well as the radiator grille together with the No. 1 radiator grille garnish.

The windshield washer pump installation begins with setting up both assembly components before linking the connector through its corresponding parts. The washer hose requires connection to both the windshield washer motor and pump assembly before filling the washer jar with fluid. Place the front bumper assembly with fog light or without fog light according to specifications then install the 2GR-FE cool air intake duct seal. The technician should apply these steps to the vehicle before moving forward with fog light aim adjustment: prepare the vehicle for inspection followed by testing and potential adjustments to the aim.

Service of the front windshield washer motor starts with removing the 2GR-FE cool air intake duct seal and then proceeding to remove the front bumper assembly with optional fog lights. The washer fluid must drain by removing the hose from the connection between windshield washer motor and pump assembly. The service proceeds with disconnecting the connector and separate installation of the windshield washer motor and pump assembly. The first step for installation requires you to place the windshield washer motor and pump assembly in position and then connect the connector. Install washer fluid in the washer jar using a washer hose connection to the assembly. The front bumper assembly requires replacement along with the fog light components if present before you install the 2GR-FE cool air intake duct seal.

The first step for windshield washer motor and pump assembly installation involves putting together the parts and attaching the connector. The washer hose installation should occur after connecting it to the windshield washer motor and pump assembly before adding washer fluid to the jar. First assemble the bumper front and afterward add the No. 4 engine under cover assembly for 2AZ-FE models and then install the radiator grille protector. For vehicles with fog lights the technician must conduct aiming checks of fog lights before performing any necessary adjustment to the aiming.

The procedure to remove the windshield washer motor and pump assembly starts with radiator grille protector removal and continues with the removal of the No. 4 engine under cover for 2AZ-FE models. This process ends with front bumper assembly removal. Washer fluid should be drained by detaching the washer hose from the windshield washer motor and pump assembly. The windshield washer motor and pump assembly removal process ends with disconnection of the connector and removal of the unit.

A technician should disconnect the connector on the windshield washer jar assembly before removing the clip and 3 bolts to extract the washer jar. Drain the washer fluid by taking out the washer hose from both the windshield washer motor and pump. The washer motor combined with pump must be withdrawn from within the washer jar packing after draining the fluid. Begin the installation by returning the windshield washer motor and pump into its designated packing inside the washer jar. Place washer fluid inside the washer jar assembly through the washer hose connector to washer motor and pump followed by reinstallation of the windshield washer jar using the connector and clip and 3 bolts with 3.5 N.m (36 kgf.cm, 31 in.lbf) torque.

The windshield washer motor repair starts by disconnecting the connector from the assembly while removing the clip followed by detaching three bolts to extract the washer jar. Drain the washer fluid by taking the washer hose off from the windshield washer motor and pump. You must pull the windshield washer motor and pump assembly out from its position within the washer jar packing to complete the removal.

Remove the windshield washer motor and pump assembly by pulling it out of the packing of the washer jar.

Fill the washer jar assembly with washer fluid.

Install the 2 bolts with a torque of 5.5 Nm (56 kgf-cm, 49 in-lbf).

Remove the right headlight unit.

Connect the 2 connectors and the 3 harness clamps.

Disconnect the 3 connectors and the 2 harness clamps.

Disconnect the washer hose from the windshield washer motor and pump assembly.

Connect the 2 harness clamps and the 3 connectors.

Remove the front bumper assembly.

First, connect the connector.

Disconnect the 2 washer hoses from the windshield washer motor and pump.

Attach the connector and harness clamps.

Disconnect the connector and remove the windshield washer motor and pump assembly.

Install the front fender liner RH.

Use a screwdriver to turn the pin 90 degrees and take out the pin hold clip.

Disconnect the washer hose from the windshield washer motor and pump if there is no rear wiper, or disconnect the 2 washer hoses if there is a rear wiper.

Position the washer motor with the gasket as indicated in the illustration, ensuring the gasket is correctly aligned, and connect the connector.

Install 9 clips and the pin hold clip.

Remove the washer hoses from the windshield washer motor and pump assembly and collect the fluid in a container.

Place the rear washer motor and pump assembly back into the packing of the washer jar, followed by the windshield washer motor and pump assembly.

Take out the cool air intake duct seal and the radiator grille.

Place it onto the packing of the washer jar.

Pull the washer motor and pump out of the packing of the washer jar.

Connect the 2 connectors and attach the clamp.

Take off the front fender mudguard LH.

The front fender liner on both the left and right sides, the radiator support opening cover, and the front bumper cover.

Install the windshield washer jar assembly with the headlight cleaner system or without it, depending on your vehicle's configuration.

Disconnect the cable from the negative battery terminal and wait at least 90 seconds to prevent airbag and seat belt pretensioner activation.

Yes, use the same procedure for both the RH and LH sides.

Install the headlight assembly RH, the front bumper cover, and the front spoiler cover if applicable.

Begin by removing the windshield washer jar assembly by disconnecting the connector, then removing the clip and 3 bolts to take out the washer jar.

Disconnect the two harness clamps, remove the connector, and then the two bolts to remove the jar.

Attach the assembly to the packing of the washer jar.

Install the radiator support opening cover.

A torque of 3.5 Nm (36 kgf-cm, 31 in-lbf) should be applied.

Disconnect the washer hose from the windshield washer motor and pump.

Connect the two connectors and harness clamps.

Connect the washer hose to the washer motor and pump, and fill the washer jar with washer fluid.

Remove the front wheel RH and the front fender outside moulding RH, applying the same procedure for the LH side.