Toyota 85330-60180
Washer Pump

Owners must start by removing the front bumper cover prior to removing the windshield washer motor. The right-hand headlight unit needs to be removed following the removal of the front bumper cover. The washer fluid needs to drain from within the system by uncoupling the 2 hoses connected to the washer motor and pump assembly. First disconnect three connectors and two harness clamps at the windshield washer jar assembly before removing its two bolts to extract that assembly. The washer motor and pump assembly needs to be extracted from between the washer jar assembly packing.

The first step to remove the windshield washer motor requires drivers to remove the No. 1 radiator grille garnish and radiator grille after which they should unfasten the front bumper cover. Following removal of the radiator grille components you must drain washer fluid through the disconnecting of 2 washer hoses from the windshield washer motor and pump. The windshield washer jar assembly removal process requires three harness clamps and two connectors released along with five bolts until the jar can be taken out. The procedure ends with pulling out the windshield washer motor and pump assembly from its packing inside the washer jar.

You should mount the windshield washer motor and pump assembly onto the washer fluid container packing. Position the windshield washer jar assembly in its place before tightening the 2 bolts to 5.5 Nm (56 kgf-cm, 49 in-lbf). Then link both harness clamps and 3 connectors to the assembly. After that hook up the washer hose to the washer unit then put washer fluid into the washer jar assembly. To complete the installation put the front bumper cover over the headlight unit RH.

The first step to install the front washer motor and pump assembly requires connector connection. Attach the washer hose to the front washer pump and motor assembly before filling the fluid jar with washer fluid. The RH front fender liner installation needs to precede the front fender moulding sub-assembly RH installation. The installer should set up the front bumper assembly either without fog lights or with fog lights if needed. The installation process requires placing the radiator grille followed by installing the cool air intake duct seal. You should now install the No. 1 engine under cover. The procedure for fog light aiming must be prepared in advance for all vehicles that have fog lights. Adjustments must be made to the aiming during this process.

The procedure for removing the windshield washer motor starts by detaching the front fender mudguard LH followed by side step assembly LH followed by body rocker panel moulding assembly LH. You must detach the front fender liner LH using a T30 "TORX" socket to eliminate 2 screws and remove first 2 grommets, then 12 clips, and finally the fender liner with a clip remover. The washer fluid can be drained by removing the hose from the windshield washer motor and pump. A clip remover allows you to remove the washer inlet sub-assembly by detaching both the clip and washer inlet. When dealing with the windshield washer jar assembly you will need to detach the clamp first then disconnect the 2 connectors together with the headlight cleaner hose when a headlight cleaner system is present or in its absence disconnect the clamp and the 1 connector. The windshield washer jar requires removal by unfastening its 4 bolts. The installation ends by removing the windshield washer motor and pump assembly with its gasket following the provided illustration.

The first step to uninstall the windshield washer motor starts with disconnecting the cable from the negative battery terminal. The windshield washer jar assembly should be taken out by disconnecting the connector and restraining both bolts. Remove washer fluid through hose detachment from windshield washer motor and pump before draining when a vehicle lacks a rear wiper or by detaching the pair of washer hoses for vehicles with rear wiper systems. To disconnect the washer wiring start by taking off the connector and unfastening the harness clamps and also remove the two connectors and clamps from vehicles with a rear wiper. Ending the washer replacement task requires pulling out the front washer motor and pump assembly from the washer jar's packing. Vehicles with rear wipers need additional rear washer motor and pump assembly removal by following the same method.

The first step to remove the windshield washer motor and pump assembly requires initial removal of the right-hand side front wheel and then the right front fender liner. A screwdriver allows users to rotate the pin 90 degrees to remove the pin hold clip while they detach 9 clips and 5 screws followed by taking out 3 grommets with the front fender liner; the grommets require replacement as they will break when removed. Washer fluid drainage begins with disconnecting the washer hose from both the windshield washer motor together with pump assembly. To finish the process disconnect the connector before clearing out the windshield washer motor and pump assembly from its location.

One must disconnect the negative cable from the battery before waiting at least ninety seconds to disable SRS system operation. The washer inlet sub-assembly needs extraction by first removing the clip then lifting the washer inlet upward off the windshield washer jar and pump assembly. The first step involves using a screwdriver to remove the clip and fender liner retainer from the left-hand side front fender liner while also removing the screw, nut, and bolt. Owners with diffusers should additionally detach the front fender splash front shield LH before partially taking out the fender liner from its mounting position. Repetitive steps should be used when removing the right-hand side fender liner. Begin by removing the radiator support opening cover and proceed to uninstall the front bumper cover according to standard procedures that depend on whether it comes with an under guard. The washer fluid drainage process requires disconnection of the washer hoses from the windshield washer motor and pump assembly and placement of the fluid into a container. The three clamps should be detached while disconnecting the three connectors attached to the windshield washer jar assembly after which the two washer hoses and three screws need removal to extract the washer jar and pump. Finally remove the windshield washer motor and pump assembly from its packing in the washer jar followed by extracts of the rear washer motor and pump assembly.

You need to start by detaching the 3 bolts and removing the washer jar assembly alongside the headlight cleaner system after disconnecting its 5 connectors and 2 clamps. When no headlight cleaning system exists you will disconnect the 3 connectors and two clamps before taking out the 3 bolts from the washer jar. The second step requires you to empty the washer liquid through the removal of hose connections. To finish the process remove the washer motor and pump from its packing inside the washer jar.

The first step to remove the windshield washer motor requires removal of the front wheel RH and front fender outside moulding RH using the same procedure for the LH side. To access the front fender liner RH users should rotate the pin hold clip 90 degrees with a screwdriver followed by removing the 4 clips and 8 screws along with the bolt and 3 grommets, although the grommets will usually break during removal. Cease the windshield washer fluid by detaching the washer tube from the motor-pump assembly and draining it into a collecting container. Disassemble the windshield washer motor and pump by following the procedure of connector disconnection then extract the assembly into a container which will collect any residual washer fluid.

Starting the service of the hatchback windshield washer motor requires disconnecting the negative battery terminal cable. Use the washer fluid drain sequence by unattaching the right-hand headlight assembly together with the front bumper cover and removing the fluid through hose connections from the windshield washer motor and pump. Start by disconnecting the two connectors alongside harness clamps which allows access to the two bolts for uninstalling the jar assembly. The windshield washer motor and pump assembly can be taken away from the washer jar by physically removing it from its packaging. To install the system begin by positioning the windshield washer pump assembly onto the washer jar packing and follow by screwing on the jar using the two bolts which should be tightened to 5.5 N.m (56 kgf.cm, 49 in.lbf). To initiate operation connect the connectors and then clamp the harnesses after you add washer fluid through connecting the hose to the motor-pump unit. Before completion, reinstall the right-hand headlight assembly while replacing the front bumper cover and connect the negative battery terminal cable and torque it to 5.4 N.m (55 kgf.cm, 48 in.lbf).

Connect the 2 connectors and the 3 harness clamps.

Position it onto the packing of the washer jar assembly.

Connect the washer hose to the washer motor and pump, and fill the washer jar with washer fluid.

Remove the windshield washer motor and pump assembly by pulling it out of the packing of the washer jar.

Install the headlight unit RH and the front bumper cover.

Fill the washer jar and pump assembly with washer fluid.

Prepare for fog light aiming adjustment, inspect the fog light aiming, and adjust as necessary.

Pull it out of the packing of the washer jar.

Disconnect the 3 connectors and the 2 harness clamps.

Attach the washer hose to the windshield washer motor and pump assembly, then fill the washer jar with washer fluid.

Connect the cable to the negative battery terminal.

Disconnect the connector and remove the rear washer motor and pump assembly.

Connect the washer hoses and fill the jar.

Remove the front fender liner LH and RH, the radiator support opening cover, and the front bumper cover.

Connect the headlight cleaner hose to the headlight cleaner motor and pump.

Attach the assembly to the packing of the washer jar.

Simply connect the connector and attach the clamp.

Pull out the windshield washer motor and pump assembly from the packing of the washer jar, and do the same for the rear washer motor and pump assembly.

Fill up the washer jar assembly with washer fluid.

Position the assembly onto the packing of the washer jar.

Install the two bolts (Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)), connect the connector, and harness clamps.

Install the windshield washer jar assembly.

Pull it out of the packing of the washer jar.

First, install the assembly.