How to service and repair the brake caliper on Toyota Sienna?

Start brake caliper servicing and repair work by taking out the cylinder boot set ring and cylinder boot with a screwdriver. After positioning the piece of cloth between the piston and caliper use compressed air to push the piston from the cylinder while maintaining your fingers safe from the piston. First use a screwdriver to remove the piston seal before using the same tool to separate the torque plate sliding pins because the reinstallation process requires the sliding pin with sliding bushing to fit into the lower section while the one without bushing fits into the upper section. Install the new dust boots into their torque plate positions through the usage of a 24 mm socket and hammer which ensures the metal plate fits tightly. When performing this task tap out both dust boots with a screwdriver and hammer. Available for inspection is the pad lining thickness measurement requiring a replacement if thickness falls below 1.0 mm (0.039 inch) or presents severe wear indications. Check the disc thickness by using a micrometer until it reaches 26.0 mm (1.024 inch) minimum or if there are scoring marks or uneven wear patterns. A dial indicator set to 10 mm (0.39 inch) from the edge should be used to measure disc runout which must not exceed a maximum runout of 0.05 mm (0.0020 inch). Disc runout adjustment requires the removal of bolts and torque plate from the knuckle followed by removal of the hub nuts and disc. Reinstall the disc with its position 1/5 turn off center from original placement and torque hub nuts to 104 Nm (1,050 kgf-cm, 77 ft. lbs.). The runout measurement should keep repeating the adjustment process until the minimum runout reaches under 0.05 mm (0.0020 inch). Installation of the disc should happen in its current position unless you need to change discs and start the runout measurement again. After assembling the torque plate install the mounting bolts with a torque of 107 Nm (1,090 kgf-cm, 79 ft. lbs.). After reverse disassembly steps the technician will rebuild the system by applying lithium soap base glycol grease and disc brake grease to the specified parts.

OEM Toyota Sienna Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Calipers found

View related parts
Toyota Sienna Caliper Assembly, Driver Side
Part Number: 47750-0E031
$212.48 MSRP: $303.38
You Save: $90.90 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Caliper; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Replaces: 47750-0E030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2020 Toyota Sienna | Base, L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Cylinder Assembly, Front Disc Brake, Passenger Side
Part Number: 47730-0E031
$216.79 MSRP: $309.53
You Save: $92.74 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper
- Position: Passenger Side
- Replaces: 47730-0E030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2020 Toyota Sienna | Base, L, LE, Limited, Limited Premium, SE, SE Premium, XLE, XLE Premium | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Caliper, Rear Driver Side
Part Number: 47750-28270
$192.21 MSRP: $274.44
You Save: $82.23 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Rear Left; Cylinder Assembly, Disc Brake, Rear Driver Side; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2010 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Caliper, Driver Side
Part Number: 47750-08030
$247.32 MSRP: $353.11
You Save: $105.79 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2010 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Caliper, Passenger Side
Part Number: 47730-28270
$192.21 MSRP: $274.44
You Save: $82.23 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Rear Right; Cylinder Assembly, Rear Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2010 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Caliper, Passenger Side
Part Number: 47730-08030
$247.32 MSRP: $353.11
You Save: $105.79 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Right; Cylinder Assembly, Front Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2010 Toyota Sienna | CE, LE, Limited, XLE, XLE Limited | 6 Cyl 3.3 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Sienna Caliper Assembly, Driver Side
Part Number: 47750-08050
$170.36 MSRP: $241.17
You Save: $70.81 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Caliper; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Caliper Assembly, Passenger Side
Part Number: 47730-08040
$170.36 MSRP: $241.17
You Save: $70.81 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Right; Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2021-2023 Toyota Sienna | 25th Anniversary Edition, LE, Limited, Platinum, XLE, XSE | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sienna Caliper, Driver Side
Part Number: 47750-08020
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2003 Toyota Sienna | CE, LE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Sienna Caliper, Driver Side
Part Number: 47750-08010
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Replaces: 47750-06050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2000 Toyota Sienna | CE, LE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Sienna Caliper, Passenger Side
Part Number: 47730-08020
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Right; Cylinder Assembly, Front Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2003 Toyota Sienna | CE, LE, XLE | 6 Cyl 3.0 L GAS
View related parts
Toyota Sienna Caliper, Passenger Side
Part Number: 47730-08010
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Right; Cylinder Assembly, Front Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Replaces: 47730-06050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2000 Toyota Sienna | CE, LE, XLE | 6 Cyl 3.0 L GAS

Toyota Sienna Brake Caliper

Choose genuine Brake Caliper that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Caliper for your Toyota Sienna? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sienna parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Toyota Sienna Brake Caliper Parts and Q&A

Caliper, Passenger Side
47730-08020
Q: How to service and repair the brake caliper on Toyota Sienna?
A:
Start brake caliper servicing and repair work by taking out the cylinder boot set ring and cylinder boot with a screwdriver. After positioning the piece of cloth between the piston and caliper use compressed air to push the piston from the cylinder while maintaining your fingers safe from the piston. First use a screwdriver to remove the piston seal before using the same tool to separate the torque plate sliding pins because the reinstallation process requires the sliding pin with sliding bushing to fit into the lower section while the one without bushing fits into the upper section. Install the new dust boots into their torque plate positions through the usage of a 24 mm socket and hammer which ensures the metal plate fits tightly. When performing this task tap out both dust boots with a screwdriver and hammer. Available for inspection is the pad lining thickness measurement requiring a replacement if thickness falls below 1.0 mm (0.039 inch) or presents severe wear indications. Check the disc thickness by using a micrometer until it reaches 26.0 mm (1.024 inch) minimum or if there are scoring marks or uneven wear patterns. A dial indicator set to 10 mm (0.39 inch) from the edge should be used to measure disc runout which must not exceed a maximum runout of 0.05 mm (0.0020 inch). Disc runout adjustment requires the removal of bolts and torque plate from the knuckle followed by removal of the hub nuts and disc. Reinstall the disc with its position 1/5 turn off center from original placement and torque hub nuts to 104 Nm (1,050 kgf-cm, 77 ft. lbs.). The runout measurement should keep repeating the adjustment process until the minimum runout reaches under 0.05 mm (0.0020 inch). Installation of the disc should happen in its current position unless you need to change discs and start the runout measurement again. After assembling the torque plate install the mounting bolts with a torque of 107 Nm (1,090 kgf-cm, 79 ft. lbs.). After reverse disassembly steps the technician will rebuild the system by applying lithium soap base glycol grease and disc brake grease to the specified parts.

Related Toyota Sienna Parts

Browse Toyota Sienna Brake Caliper by Years

2023 2022 2021 2020 2019 2018 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998