How to install the Brake Master Cylinder on Toyota FJ Cruiser?

You must start the hydraulic brake booster assembly by laying down a new gasket followed by installation of 4 nuts that require torquing to 14 Nm (145 kgf-cm, 10 ft-lbf). The installation process requires temporarily fastening brake tubes into their designated spots on the brake actuator before joining them to the hydraulic brake booster utilizing a union nut wrench that should be tightened to 15 Nm (155 kgf-cm, 11 ft-lbf) wrench-free or 14 Nm (144 kgf-cm, 10 ft-lbf) with the wrench at a 90-degree angle to the torque wrench to ensure accuracy. After hooking up the three connectors install the master cylinder push rod clevis before connecting the cable to the negative battery terminal then tighten it with 3.9 Nm (40 kgf-cm, 35 in-lbf) torque. Brake fluid should be added to the reservoir followed by bleaching the brake booster through the accumulator pump assembly and brake line with the brake master cylinder solenoid as the final step. You should observe the brake fluid level in the reservoir while also looking for any fluid leakage signs. The brake pedal needs an inspection with following adjustment before completing installation of the instrument panel lower finish panel sub-assembly and the hood lock control lever sub-assembly along with the instrument panel No. 1 register assembly. The sequence includes installing the front door opening trim Weather Strip together with the cowl side trim board and footrest clip and front floor footrest and front door scuff plate. Inspect the operation of the brake master cylinder as your last procedure.

How to service and repair the brake master cylinder on Toyota FJ Cruiser?

The procedure to work on the brake master cylinder begins by disabling the ignition switch followed by performing twenty or more brake pedal depressions before starting. High-pressure conditions must be managed to prevent deformation of the brake actuator No. 1 tube while the ignition switch should remain off until all work finishes. Begin the procedure by disconnecting the cable from the negative battery terminal then drain the brake fluid while doing proper fluid cleanup of painted surfaces. Start the procedure by taking out the front door scuff plate along with the front floor footrest and footrest clip and cowl side trim board. First strip the Weather Strip from the front door opening and then take away the instrument panel No. 1 register assembly before disconnecting the hood lock control lever sub-assembly. Before further work remove the instrument panel lower finish panel sub-assembly while also disassembling the master cylinder push rod clevis. To remove the hydraulic brake booster first disconnect all three connectors then use a union nut wrench to disconnect its four brake tubes. Always label the lines before removing their four nuts and pulling out the hydraulic brake booster together with its gasket.

OEM Toyota FJ Cruiser Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

43 Brake Master Cylinders found

View related parts
Toyota FJ Cruiser Brake Booster
Part Number: 47050-35180
$1506.52 MSRP: $2207.82
You Save: $701.30 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Booster; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Power Booster
Part Number: 47050-35090
$1736.85 MSRP: $2545.37
You Save: $808.52 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35232
$752.38 MSRP: $1102.62
You Save: $350.24 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2014 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Brake Booster
Part Number: 47050-35182
$1370.73 MSRP: $2008.82
You Save: $638.09 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Booster; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2014 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Power Booster
Part Number: 47050-35110
$1698.01 MSRP: $2488.45
You Save: $790.44 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35100
$941.43 MSRP: $1379.67
You Save: $438.24 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2008 Toyota FJ Cruiser | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35141
$941.63 MSRP: $1379.97
You Save: $438.34 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35101
$941.97 MSRP: $1380.46
You Save: $438.49 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008 Toyota FJ Cruiser | Base, Trail Teams Special Edition | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Brake Booster
Part Number: 47050-35111
$1506.26 MSRP: $2207.45
You Save: $701.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35151
$941.43 MSRP: $1379.67
You Save: $438.24 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: DIFFERENTIAL LOCK-WITH
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2011 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35260
$761.35 MSRP: $1115.76
You Save: $354.41 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: VSC-WITH(A-TRC & CRAWL CONTROL),REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2014 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35241
$1191.63 MSRP: $1746.34
You Save: $554.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Brake Booster
Part Number: 47050-35091
$1201.39 MSRP: $1760.64
You Save: $559.25 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35242
$1182.09 MSRP: $1732.37
You Save: $550.28 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2014 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35120
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35140
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Power Booster
Part Number: 47050-35120
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Booster; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: DIFFERENTIAL LOCK-WITH
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35111
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: DIFFERENTIAL LOCK-WITH
- Replaces: 47025-35110
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2007-2008 Toyota FJ Cruiser | Base, Trail Teams Special Edition, TRD Special Edition | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Master Cylinder
Part Number: 47025-35131
$1205.93 MSRP: $1767.30
You Save: $561.37 (32%)
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: DIFFERENTIAL LOCK-WITH
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2011 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS
View related parts
Toyota FJ Cruiser Brake Booster
Part Number: 47050-35200
$1168.93 MSRP: $1713.07
You Save: $544.14 (32%)
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Booster; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: VSC-WITH(A-TRC & CRAWL CONTROL),REFER TO PNC 47217
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2014 Toyota FJ Cruiser | Base | 6 Cyl 4.0 L GAS

| Page 1 of 3 |Next >

1-20 of 43 Results

Toyota FJ Cruiser Brake Master Cylinder

Choose genuine Brake Master Cylinder that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Master Cylinder for your Toyota FJ Cruiser? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota FJ Cruiser parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Due to this fact, the Brake Master Cylinder of the Toyota FJ Cruiser is one of the significant parts that plays a key role in establishing the reliable braking system for the Toyota FJ Cruiser. That is the function of the current Brake Master Cylinder to translate the foot pressure of the driver into hydraulic pressure that will in turn, push brake fluid through the system leading to the slave cylinders that in turn will engage the brakes. Interestingly, the Toyota FJ Cruiser is equipped with a dual circuit Brake Master Cylinder which helps to provide optimized safety in case of failure of one of the circuits, since the other one will be able to supply enough force for braking. This feature is necessary to keep the consumption rate and risk level low, which could be important when driving on an offroad which is strong side of FJ Cruiser. Brake Master Cylinder is available in several FJ Cruiser model, which means that the vehicle's brake will work in a similar response to different models of the FJ Cruiser. It is recommended that the Brake Master Cylinder should be checked periodically so that problems like leakage of the fluid or failure of internal components of the Brake Master Cylinder should not hinder the braking system. The Toyota FJ Cruiser has its 4.0-liter V6 engine and nearly invulnerable design and distinctive looks, functional in its interiors which assure off-road sturdiness. Brake Master Cylinder is also largely issue within shaping the driving characteristics of the vehicle and thus helps to make the Toyota FJ Cruiser quite unique and desirable within the current automobile market. The integration of reliability, safety features, and performance places the Toyota FJ Cruiser at the top of the most demanded vehicles by the fans and regular drivers.

Toyota FJ Cruiser Brake Master Cylinder Parts and Q&A

Master Cylinder
47025-35081
Q: How to install the Brake Master Cylinder on Toyota FJ Cruiser?
A:
You must start the hydraulic brake booster assembly by laying down a new gasket followed by installation of 4 nuts that require torquing to 14 Nm (145 kgf-cm, 10 ft-lbf). The installation process requires temporarily fastening brake tubes into their designated spots on the brake actuator before joining them to the hydraulic brake booster utilizing a union nut wrench that should be tightened to 15 Nm (155 kgf-cm, 11 ft-lbf) wrench-free or 14 Nm (144 kgf-cm, 10 ft-lbf) with the wrench at a 90-degree angle to the torque wrench to ensure accuracy. After hooking up the three connectors install the master cylinder push rod clevis before connecting the cable to the negative battery terminal then tighten it with 3.9 Nm (40 kgf-cm, 35 in-lbf) torque. Brake fluid should be added to the reservoir followed by bleaching the brake booster through the accumulator pump assembly and Brake Line with the brake master cylinder solenoid as the final step. You should observe the brake fluid level in the reservoir while also looking for any fluid leakage signs. The brake pedal needs an inspection with following adjustment before completing installation of the instrument panel lower finish panel sub-assembly and the hood lock control lever sub-assembly along with the instrument panel No. 1 register assembly. The sequence includes installing the front door opening trim Weather Strip together with the cowl side trim board and footrest clip and front floor footrest and front door scuff plate. Inspect the operation of the brake master cylinder as your last procedure.
Master Cylinder
47025-35111
Q: How to service and repair the brake master cylinder on Toyota FJ Cruiser?
A:
The procedure to work on the brake master cylinder begins by disabling the Ignition Switch followed by performing twenty or more brake pedal depressions before starting. High-pressure conditions must be managed to prevent deformation of the brake actuator No. 1 tube while the ignition switch should remain off until all work finishes. Begin the procedure by disconnecting the cable from the negative battery terminal then drain the brake fluid while doing proper fluid cleanup of painted surfaces. Start the procedure by taking out the front door scuff plate along with the front floor footrest and footrest clip and cowl side trim board. First strip the Weather Strip from the front door opening and then take away the instrument panel No. 1 register assembly before disconnecting the hood lock control lever sub-assembly. Before further work remove the instrument panel lower finish panel sub-assembly while also disassembling the master cylinder push rod clevis. To remove the hydraulic brake booster first disconnect all three connectors then use a union nut wrench to disconnect its four brake tubes. Always label the lines before removing their four nuts and pulling out the hydraulic brake booster together with its gasket.

Related Toyota FJ Cruiser Parts

Browse Toyota FJ Cruiser Brake Master Cylinder by Years

2014 2013 2012 2011 2010 2009 2008 2007