How to service and repair the brake caliper on Toyota Corolla?

Start the brake caliper servicing and repair with screwdriver removal of the cylinder boot set ring combined with cylinder boot. Fit a piece of cloth between the piston and caliper before removing the piston through the cylinder with compressed air while avoiding placing fingers in front of the piston. The piston seal must be removed first with a screwdriver before extracting both sliding pins from the torque plate. Note that during reassembly the lower part accepts the sliding pin with bushing and the upper part takes the pin without bushing. After tapping the 2 dust boots with a screwdriver and hammer you can install new dust boots through the use of a 19 mm socket and hammer followed by careful placement of the metal plate portion inside the torque plate. A ruler should be used to check the pad lining thickness and failure should occur when measurements fall below 12.0 mm or are 1.0 mm or less and the pads should be replaced at such times. The disc thickness should be measured with a micrometer to ensure it remains above 20.0 but below 22.0 mm and without scores while adhering to the 20.0 mm minimum standard. Uneven wear or scores indicate replacement. The disc runout requires measurement by a dial indicator set 10 mm away from the edge and accepts runout readings up to 0.05 mm. Exceeding this amount demands inspection of bearing play and axle hub runout followed by necessary adjustment or grinding procedures. To perform adjustments release the knuckle torque plate and two bolts after which the technician removes hub nuts and disc before reinstalling the disc in a rotated position by 1/4 from its original location and torques the hub nuts to 103 Nm. The procedure requires runout remeasurement until the minimum reading reaches below 0.05 mm then the torque plate installation followed by torque bolt application to 88 Nm. The reverse operation sequence of disassembly enables reassembly with grease application on indicated parts using lithium soap base glycol grease together with disc brake grease.

OEM Toyota Corolla Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

36 Brake Calipers found

View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12310
$259.54 MSRP: $370.56
You Save: $111.02 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Manufacturer Note: *86 & *87
- Position: Driver Side
- Replaces: 47750-12350, 47750-01020, 47750-01030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1992 Toyota Corolla | Base, DLX, DLX All Trac, FX16, FX16 GTS, GTS, LE, SR5, SR5 All Trac | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12320
$152.43 MSRP: $215.78
You Save: $63.35 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1991 Toyota Corolla | GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12320
$152.43 MSRP: $215.78
You Save: $63.35 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1991 Toyota Corolla | GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-02020
$153.13 MSRP: $216.76
You Save: $63.63 (30%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc Brake, Left-Hand; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1988 Toyota Corolla | FX16, FX16 GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-02050
$266.19 MSRP: $380.06
You Save: $113.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Right; Cylinder Assembly, Front Disc Brake, Passenger Side; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2002 Toyota Corolla | CE, LE, S, VE | 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12450
$259.43 MSRP: $370.41
You Save: $110.98 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Manufacturer Note: (J)
- Position: Driver Side
- Replaces: 47750-02040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1993-1997 Toyota Corolla | Base, CE, DX, LE | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-02020
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1988 Toyota Corolla | FX16, FX16 GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12180
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1987 Toyota Corolla | Sport DLX, Sport GTS, Sport SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12210
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1988 Toyota Corolla | DLX, FX, FX16, FX16 GTS, LE, LE Limited | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L DIESEL
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12280
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Rear Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1988 Toyota Corolla | FX, FX16, FX16 GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12330
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Rear Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1991 Toyota Corolla | Base, DLX, DLX All Trac, GTS, LE, SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12370
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Front Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1992 Toyota Corolla | Base, DLX, DLX All Trac, LE, SR5 All Trac | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12180
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1987 Toyota Corolla | Sport DLX, Sport GTS, Sport SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12210
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1988 Toyota Corolla | DLX, FX, FX16, FX16 GTS, LE, LE Limited | 4 Cyl 1.6 L GAS, 4 Cyl 1.8 L DIESEL
View related parts
Toyota Corolla Caliper, Rear Driver Side
Part Number: 47750-12280
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Rear Driver Side
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1987-1988 Toyota Corolla | FX, FX16, FX16 GTS | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Rear Driver Side
Part Number: 47750-12330
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Rear Driver Side
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1988-1991 Toyota Corolla | Base, DLX, DLX All Trac, GTS, LE, SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-12370
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Driver Side
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1990-1992 Toyota Corolla | Base, DLX, DLX All Trac, LE, SR5 All Trac | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Passenger Side
Part Number: 47730-12231
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Rear Disc Brake, Passenger Side
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1987 Toyota Corolla | Sport DLX, Sport GTS, Sport SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Rear Driver Side
Part Number: 47750-12231
Product Specifications
- Other Name: Cylinder Assembly, Disc; Brake Caliper; Cylinder Assembly, Disc Brake, Rear Driver Side
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1987 Toyota Corolla | Sport DLX, Sport GTS, Sport SR5 | 4 Cyl 1.6 L GAS
View related parts
Toyota Corolla Caliper, Driver Side
Part Number: 47750-02050
Product Specifications
- Other Name: Cylinder Assembly, Disc; Disc Brake Caliper, Front Left; Cylinder Assembly, Disc Brake, Driver Side; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1998-2002 Toyota Corolla | CE, LE, S, VE | 4 Cyl 1.8 L GAS

| Page 1 of 2 |Next >

1-20 of 36 Results

Toyota Corolla Brake Caliper

Choose genuine Brake Caliper that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Caliper for your Toyota Corolla? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Corolla parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Brake Caliper of Toyota Corolla automobile imports a disc brake system caliper that is tasked with the responsibility of slowing down or stopping the automobile through applying force to squeeze the brake pads onto the rotors. There are two main types of brake calipers used in Corolla models: He uses two types of prices, namely, fixed prices and floating prices. Fixed calipers have their pistons on each side of the rotor for more efficiency, but are not as flexible to surface irregularities. On the other hand, there are floating calipers and those who have got pistons on one side of the rotor tend to stick and hence cause poor fuel efficiency and not uniform wear of the pads. If the car pulls to one side, the brake fluid leaks, or there are grinding noises, it is suggested to change the brake calipers for a trouble-free operation of the Toyota Corolla for many miles.

Toyota Corolla Brake Caliper Parts and Q&A

Caliper, Driver Side
47750-02050
Q: How to service and repair the brake caliper on Toyota Corolla?
A:
Start the brake caliper servicing and repair with screwdriver removal of the cylinder boot set ring combined with cylinder boot. Fit a piece of cloth between the piston and caliper before removing the piston through the cylinder with compressed air while avoiding placing fingers in front of the piston. The piston seal must be removed first with a screwdriver before extracting both sliding pins from the torque plate. Note that during reassembly the lower part accepts the sliding pin with bushing and the upper part takes the pin without bushing. After tapping the 2 dust boots with a screwdriver and hammer you can install new dust boots through the use of a 19 mm socket and hammer followed by careful placement of the metal plate portion inside the torque plate. A ruler should be used to check the pad lining thickness and failure should occur when measurements fall below 12.0 mm or are 1.0 mm or less and the pads should be replaced at such times. The disc thickness should be measured with a micrometer to ensure it remains above 20.0 but below 22.0 mm and without scores while adhering to the 20.0 mm minimum standard. Uneven wear or scores indicate replacement. The disc runout requires measurement by a dial indicator set 10 mm away from the edge and accepts runout readings up to 0.05 mm. Exceeding this amount demands inspection of bearing play and axle hub runout followed by necessary adjustment or grinding procedures. To perform adjustments release the knuckle torque plate and two bolts after which the technician removes hub nuts and disc before reinstalling the disc in a rotated position by 1/4 from its original location and torques the hub nuts to 103 Nm. The procedure requires runout remeasurement until the minimum reading reaches below 0.05 mm then the torque plate installation followed by torque bolt application to 88 Nm. The reverse operation sequence of disassembly enables reassembly with grease application on indicated parts using lithium soap base glycol grease together with disc brake grease.