Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Center Right Outer; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: GRAY,TRIM13
Position: Outer Passenger Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2003-2009 Toyota 4Runner | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Center Left Outer; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Manufacturer Note: FAWN,TRIM4#
Position: Outer Driver Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2003-2009 Toyota 4Runner | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
Other Name: Belt Assembly, Front Seat; Seat Belt Lap and Shoulder Belt, Front Left; Belt & Retractor; Belt Assembly, Front Seat Outer, Driver Side
Manufacturer Note: FAWN,TRIM4#
Position: Driver Side
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2003 Toyota 4Runner | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
| Page 1 of 9 |Next >
1-20 of 176 Results
Toyota 4Runner Seat Belt
Choose genuine Seat Belt that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Seat Belt for your Toyota 4Runner? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota 4Runner parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.
Q: How to Remove the Rear Seat Inner Seat Belt Assembly on Toyota 4Runner?
A:
The first step to remove the rear seat inner belt assembly for the Rear No. 1 Seat is to uninstall the rear No. 1 seat assembly followed by the rear No. 1 seat cushion assembly LH. Unfasten the bolt then remove the belt to get rid of the rear seat inner belt assembly. The method applied to remove the LH rear seat inner belt assembly must be duplicated for the RH side.
Q: What is the correct method for installing a new seat belt tongue plate stopper and inspecting the seat belt webbing for damage on Toyota 4Runner?
A:
The new service part of the seat belt tongue plate stopper requires installation procedures to support seat belt maintenance. The tongue plate needs positioning on the upper end of the tongue plate stopper while being held by clips or tape until replacement is ready. Use pliers to remove all leftover parts from your original tongue plate stopper that is present in the webbing. A seat belt assembly must be replaced whenever webbing exhibits cut or frayed or damaged tissue or if it sustained serious impact; complete webbing inspection should reveal damage before installing a new assembly while avoiding webbing damage in the repair process. Secure a new tongue plate stopper in the webbing hole by placing it the right way before finishing installation. Use an adjustable wrench to pinch the tongue plate stopper inside the webbing before aligning the male and female pieces parallel through hand twisting and pushing of the adjustment screw. Pliers should not be used due to potential damage of the webbing material. The adjustment screw of the adjustable wrench needs adjustable joint pliers to achieve a controlled screw tightening which establishes the adjustable wrench jaw opening at 4.5 - 5.0 mm (0.18 in. - 0.20 in.). Verify that the male pin of the tongue plate stopper has properly stretched into the female part to firmly secure onto the webbing belt.