How to remove the front seat cushion assembly with the Occupant Classification ECU and Occupant Classification Sensor on Scion xB?

Disassembly of the front seat cushion assembly with the Occupant Classification ECU and Occupant Classification Sensor requires you to disconnect the cable from the negative battery terminal while waiting for 90 seconds to avoid accidental Air Bag deployment. The following procedure requires dismantling of seat headrest assembly and seat track cover and seat track inner bracket cover. Proceed to detach the occupant classification ECU by disconnecting its connector along with removing the two bolts. The procedure requires users to take out the reclining adjuster release handle alongside the front seat inner belt assembly along with both left and right front seat cushion shields. The last step entails disconnecting the connector from the occupant classification sensor followed by wireless harness clamp removal and seat cushion frame clamp release and extraction of the 2 clips and occupant classification sensor.

How to install the front seat cushion assembly with the occupant classification ECU and sensor on Scion xB?

Installation of the front seat cushion assembly with occupant classification ECU and sensor starts with new parts from prepared service kits while SRS components must never derive from other vehicles. Before using an occupant classification sensor in replacement work verify that it did not experience a crash or show any evidence of damage. During installation secure the SRS wires so they avoid both other components and the wire pinch points. Install the occupant classification sensor by first attaching it with 2 clips before levering the claw to the seat cushion frame and afterward joining the connector. The installation process begins with adding the front seat cushion cover pad followed by the front seat cushion shield LH before the front seat inner belt assembly and front seat cushion shield RH and reclining adjuster release handle installation. Fasten the occupant classification ECU with its 2 bolts at 3.0 Nm (31 kgf-cm, 27 in-lbf) torque level and attach its connector. Put in place the front seat assembly RH followed by the front seat headrest assembly and seat track cover before installing the seat track inner bracket cover. Complete the process by connecting the cable to the negative battery terminal with 5.4 Nm torque then running zero point calibration followed by the sensitivity check and finally inspecting the SRS warning light.

OEM Scion xB Seat Cushion

Seat Pad Cushion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Seat Cushions found

View related parts
Scion xB Seat Cushion, Rear
Part Number: 71601-12061-B0
$663.96 MSRP: $973.05
You Save: $309.09 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Sub-Assembly, Rear Seat; Seat Cushion Foam, Rear
- Position: Rear
- Replaces: 71601-12060-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Back Pad, Front
Part Number: 71568-12081-B1
$401.67 MSRP: $588.65
You Save: $186.98 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad, Front Seat Back W/; Seat Back Cushion, Front Left
- Position: Front
- Replaces: 71568-12080-B1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Cushion, Front
Part Number: 71001-1AW01-B0
$708.46 MSRP: $1038.25
You Save: $329.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Seat Set; Seat Cushion Foam, Front Right
- Position: Front
- Replaces: 71001-1AW00-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Back Pad, Driver Side
Part Number: 71652-12A10
$174.71 MSRP: $247.33
You Save: $72.62 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad, Rear Seat Back, L; Seat Back Cushion, Rear Left; Pad, Rear Seat Back, Driver Side(For Separate Type)
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2015 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Back Pad, Passenger Side
Part Number: 71651-12880
$256.99 MSRP: $366.92
You Save: $109.93 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad, Rear Seat Back, R; Seat Back Cushion, Rear Right; Pad, Rear Seat Back, Passenger Side(For Separate Type)
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2015 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Cushion Frame, Rear
Part Number: 71407-12180-B1
$401.78 MSRP: $588.81
You Save: $187.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cushion Sub-Assembly, Rear; Seat Frame, Rear; Cushion Assembly, Rear Seat (For Bench Type)
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2015 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Cushion Frame, Rear
Part Number: 71407-12170-B0
$463.56 MSRP: $679.35
You Save: $215.79 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cushion Sub-Assembly, Rear; Seat Frame, Rear; Cushion Assembly, Rear Seat (For Bench Type)
- Manufacturer Note: DK.GRAY,TRIM1#
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Cushion, Passenger Side
Part Number: 71001-1EV20-B1
$572.71 MSRP: $839.31
You Save: $266.60 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Seat Set; Seat Cushion Foam, Front Right; Cushion Assembly, Front Seat, Passenger Side(For Separate Type)
- Manufacturer Note: DK.GRAY,TRIM1#
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2015 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Cushion, Passenger Side
Part Number: 71001-1EV20-B0
$572.71 MSRP: $839.31
You Save: $266.60 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Seat Set; Seat Cushion Foam, Front Right; Cushion Assembly, Front Seat, Passenger Side(For Separate Type)
- Manufacturer Note: DK.GRAY,TRIM1#
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2011-2012 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Back Pad, Front
Part Number: 71558-12081-B1
Product Specifications
- Other Name: Pad, Front Seat Back W/; Seat Back Cushion, Front Right
- Position: Front
- Replaces: 71558-12080-B1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS
View related parts
Scion xB Seat Cushion, Front
Part Number: 71528-12141-B0
Product Specifications
- Other Name: Pad, Front Seat Cushion; Seat Cushion Foam, Front Left
- Position: Front
- Replaces: 71528-12140-B0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2010 Scion xB | Base | 4 Cyl 2.4 L GAS

Scion xB Seat Cushion

Choose genuine Seat Cushion that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Seat Cushion for your Scion xB? Our website is your one-stop destination. We stock an extensive selection of genuine Scion xB parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Scion xB Seat Cushion is an essential part created to make a difference in driving for different Scion xB models that are popular for their solidity and speed. This Seat Cushion helps to relieve some common difficulties, which are usually felt during lengthy car traveling, for example, pain in the back and tiredness due to car seats unbearable hardness. Having the beaded and sheepskin models, the Scion xB Seat Cushion is questionable for driving in hot and cold weather as it enhances circulation and temperature of the seat. The beads enable ventilation and the sheepskin one has the ability to absorb moisture making it possible to meet all the different feels of the Scion xB owners. Compatibility with multiple xB generations confirms that drivers of any generation of these cars will be able to gain the benefits of this Seat Cushion. Apart from the comfort aspect, the Scion xB Seat Cushion has added functions of increasing the effectiveness of controlling the vehicle and preventing the driver's constructive inattention while driving. This gives it prestige in the automotive industry especially for those customers who are in search of a product that endures the test of time while at the same time be comfortable to use. Owing to its well-developed design and functional characteristics, the Scion xB Seat Cushion is perfect for all those who want to enhance their trips in a Scion xB car since it is comfortable as well as safe.

Scion xB Seat Cushion Parts and Q&A

Seat Cushion, Front
71001-1AW01-B0
Q: How to remove the front seat cushion assembly with the Occupant Classification ECU and Occupant Classification Sensor on Scion xB?
A:
Disassembly of the front seat cushion assembly with the Occupant Classification ECU and Occupant Classification Sensor requires you to disconnect the cable from the negative battery terminal while waiting for 90 seconds to avoid accidental Air Bag deployment. The following procedure requires dismantling of seat headrest assembly and seat track cover and seat track inner bracket cover. Proceed to detach the occupant classification ECU by disconnecting its connector along with removing the two bolts. The procedure requires users to take out the reclining adjuster release handle alongside the front seat inner belt assembly along with both left and right front seat cushion shields. The last step entails disconnecting the connector from the occupant classification sensor followed by wireless harness clamp removal and seat cushion frame clamp release and extraction of the 2 clips and occupant classification sensor.
Seat Back Pad, Front
71568-12081-B1
Q: How to install the front seat cushion assembly with the occupant classification ECU and sensor on Scion xB?
A:
Installation of the front seat cushion assembly with occupant classification ECU and sensor starts with new parts from prepared service kits while SRS components must never derive from other vehicles. Before using an occupant classification sensor in replacement work verify that it did not experience a crash or show any evidence of damage. During installation secure the SRS wires so they avoid both other components and the wire pinch points. Install the occupant classification sensor by first attaching it with 2 clips before levering the claw to the seat cushion frame and afterward joining the connector. The installation process begins with adding the front seat cushion cover pad followed by the front seat cushion shield LH before the front seat inner belt assembly and front seat cushion shield RH and reclining adjuster release handle installation. Fasten the occupant classification ECU with its 2 bolts at 3.0 Nm (31 kgf-cm, 27 in-lbf) torque level and attach its connector. Put in place the front seat assembly RH followed by the front seat headrest assembly and seat track cover before installing the seat track inner bracket cover. Complete the process by connecting the cable to the negative battery terminal with 5.4 Nm torque then running zero point calibration followed by the sensitivity check and finally inspecting the SRS warning light.

Related Scion xB Parts

Browse Scion xB Seat Cushion by Years

2015 2014 2013 2012 2011 2010 2009 2008