How to install the exhaust pipe and its components on 2009 Toyota 4Runner?

The installation of the exhaust pipe begins with attaching the heated oxygen sensor for Bank 2 to the exhaust pipe front while applying 44 Nm (450 kgf-cm, 33 ft-lbf) torque and connecting the sensor connector and inspecting the wire for twisting; re-install the sensor if twisting occurs. You must first apply the front pipe to the exhaust manifold after placing a new gasket and then tighten the exhaust pipe front with 2 nuts at 62 Nm (630 kgf-cm, 46 ft-lbf). Apply the same torque specifications while repeating the check on the wires for the heated oxygen sensor of Bank 1. To assembly the No. 2 exhaust front pipe you need two new gaskets and should install it to the exhaust manifold using 2 bolts and 2 nuts tightened to 62 Nm (630 kgf-cm, 46 ft-lbf) for the nuts and 48 Nm (490 kgf-cm, 35 ft-lbf) for the bolts. Proceed to measure the compression spring length with the vernier caliper before installation to validate its free length minimum requirement of 40.5 mm (4.5645 in.); replace the spring if it falls below this limit. Affix the exhaust pipe assembly front with new gasket and fasten 2 bolts and 2 springs through tightening them to 43 Nm (440 kgf-cm, 32 ft-lbf). A new gasket should be installed on the exhaust pipe center before attaching the tail pipe using 2 bolts torqued to 48 Nm (490 kgf-cm, 35 ft-lbf). Check for exhaust gas leaks.

OEM 2009 Toyota 4Runner Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Exhaust Pipes found

View related parts
2009 Toyota 4Runner Resonator & Pipe
Part Number: 17430-50220
$261.65 MSRP: $342.17
You Save: $80.52 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Tail; Direct-Fit Exhaust; System Kit; Resonator; Muffler; Muffler & Tail Pipe; Tailpipe; Pipe Assembly, Exhaust, Tail
- Part Name Code: 17430
- Item Weight: 10.60 Pounds
- Item Dimensions: 44.5 x 13.3 x 9.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17430-50220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
2009 Toyota 4Runner Crossover Pipe, Front Driver Side
Part Number: 17450-50121
$1296.39 MSRP: $1740.12
You Save: $443.73 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter, Left; Exhaust Pipe; Front Pipe; Converter & Pipe; Cross Over Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Position: Front Driver Side
- Part Name Code: 17450B
- Item Weight: 11.50 Pounds
- Item Dimensions: 40.0 x 14.3 x 8.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17450-50121
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 8 Cyl 4.7 L GAS
View related parts
2009 Toyota 4Runner Intermediate Pipe, Center
Part Number: 17420-50260
$547.06 MSRP: $734.32
You Save: $187.26 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Muffler Assembly; Direct-Fit Exhaust; System Kit; Tail Pipe; Muffler & Pipe Assembly; Muffler & Tail Pipe; Muffler & Pipe; Pipe Assembly, Exhaust, Center; Muffler
- Position: Center
- Part Name Code: 17420
- Item Weight: 17.50 Pounds
- Item Dimensions: 53.5 x 20.8 x 9.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-50260
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
View related parts
2009 Toyota 4Runner Resonator & Pipe
Part Number: 17430-31410
$257.57 MSRP: $336.83
You Save: $79.26 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Tail; Direct-Fit Exhaust System Kit; Resonator; Muffler; Muffler & Tail Pipe; Pipe Assembly, Exhaust, Tail
- Part Name Code: 17430
- Item Weight: 10.40 Pounds
- Item Dimensions: 46.6 x 12.9 x 9.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17430-31410
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS
View related parts
2009 Toyota 4Runner Front Pipe, Driver Side
Part Number: 17450-31030
$1284.01 MSRP: $1723.52
You Save: $439.51 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter, Left, Rear Left; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Manufacturer Note: *114=TOYOTA/T38/Y
- Position: Front Driver Side
- Part Name Code: 17450B
- Item Weight: 7.30 Pounds
- Item Dimensions: 35.4 x 5.1 x 17.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17450-31030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS
View related parts
2009 Toyota 4Runner Front Pipe
Part Number: 17410-50450
$1207.86 MSRP: $1621.29
You Save: $413.43 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Right; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Position: Front
- Part Name Code: 17410
- Item Weight: 8.30 Pounds
- Item Dimensions: 34.8 x 7.5 x 18.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-50450
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 8 Cyl 4.7 L GAS
View related parts
2009 Toyota 4Runner Front Pipe
Part Number: 17410-31450
$1197.53 MSRP: $1607.43
You Save: $409.90 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Rear Right, Right; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Manufacturer Note: *114=TOYOTA/T37/Y
- Position: Front
- Part Name Code: 17410
- Item Weight: 10.00 Pounds
- Item Dimensions: 35.0 x 5.3 x 19.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-31450
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS
View related parts
2009 Toyota 4Runner Pipe Assembly, Exhaust, Center
Part Number: 17420-50220
$541.61 MSRP: $727.00
You Save: $185.39 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler Assembly; Exhaust System Kit; Exhaust Pipe; Tail Pipe; Muffler
- Position: Center
- Part Name Code: 17420
- Item Weight: 16.10 Pounds
- Item Dimensions: 54.5 x 21.6 x 9.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-50220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota 4Runner Submodels:
- Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS

2009 Toyota 4Runner Exhaust Pipe

Looking for affordable OEM 2009 Toyota 4Runner Exhaust Pipe? Explore our comprehensive catalogue of genuine 2009 Toyota 4Runner Exhaust Pipe. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota 4Runner Exhaust Pipe Parts Q&A

Q: How to install the exhaust pipe and its components on 2009 Toyota 4Runner?
A: The installation of the exhaust pipe begins with attaching the heated oxygen sensor for Bank 2 to the exhaust pipe front while applying 44 Nm (450 kgf-cm, 33 ft-lbf) torque and connecting the sensor connector and inspecting the wire for twisting; re-install the sensor if twisting occurs. You must first apply the front pipe to the exhaust manifold after placing a new gasket and then tighten the exhaust pipe front with 2 nuts at 62 Nm (630 kgf-cm, 46 ft-lbf). Apply the same torque specifications while repeating the check on the wires for the heated oxygen sensor of Bank 1. To assembly the No. 2 exhaust front pipe you need two new gaskets and should install it to the exhaust manifold using 2 bolts and 2 nuts tightened to 62 Nm (630 kgf-cm, 46 ft-lbf) for the nuts and 48 Nm (490 kgf-cm, 35 ft-lbf) for the bolts. Proceed to measure the compression spring length with the vernier caliper before installation to validate its free length minimum requirement of 40.5 mm (4.5645 in.); replace the spring if it falls below this limit. Affix the exhaust pipe assembly front with new gasket and fasten 2 bolts and 2 springs through tightening them to 43 Nm (440 kgf-cm, 32 ft-lbf). A new gasket should be installed on the exhaust pipe center before attaching the tail pipe using 2 bolts torqued to 48 Nm (490 kgf-cm, 35 ft-lbf). Check for exhaust gas leaks.

Alternate Year Models

2008 Toyota 4Runner Exhaust Pipe 2010 Toyota 4Runner Exhaust Pipe