How to install the exhaust pipe and its components on Toyota 4Runner?

The installation of the exhaust pipe begins with attaching the heated oxygen sensor for Bank 2 to the exhaust pipe front while applying 44 Nm (450 kgf-cm, 33 ft-lbf) torque and connecting the sensor connector and inspecting the wire for twisting; re-install the sensor if twisting occurs. You must first apply the front pipe to the exhaust manifold after placing a new gasket and then tighten the exhaust pipe front with 2 nuts at 62 Nm (630 kgf-cm, 46 ft-lbf). Apply the same torque specifications while repeating the check on the wires for the heated oxygen sensor of Bank 1. To assembly the No. 2 exhaust front pipe you need two new gaskets and should install it to the exhaust manifold using 2 bolts and 2 nuts tightened to 62 Nm (630 kgf-cm, 46 ft-lbf) for the nuts and 48 Nm (490 kgf-cm, 35 ft-lbf) for the bolts. Proceed to measure the compression spring length with the vernier caliper before installation to validate its free length minimum requirement of 40.5 mm (4.5645 in.); replace the spring if it falls below this limit. Affix the exhaust pipe assembly front with new gasket and fasten 2 bolts and 2 springs through tightening them to 43 Nm (440 kgf-cm, 32 ft-lbf). A new gasket should be installed on the exhaust pipe center before attaching the tail pipe using 2 bolts torqued to 48 Nm (490 kgf-cm, 35 ft-lbf). Check for exhaust gas leaks.

How to remove the exhaust pipe assembly on Toyota 4Runner?

The first step for exhaust pipe assembly removal requires removing 2 bolts, exhaust pipe support along with tail pipe. Begin by removing the 2 bolts with their respective 2 compression springs and then proceed to the 4 exhaust pipe supports and exhaust pipe center. The assembly of the No. 2 exhaust front pipe requires removal of its two bolts and two nuts along with the entire assembly. The Bank 1 heated oxygen sensor connector needs disconnection while the heated oxygen sensor needs removal. Continue with the procedure by removing the exhaust pipe assembly front along with its installed 2 nuts. The removal process ends with removing the heated oxygen sensor after disconnecting its connector for Bank 2.

OEM Toyota 4Runner Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

65 Exhaust Pipes found

View related parts
Toyota 4Runner Muffler & Tail Pipe, Center
Part Number: 17403-62170
$551.14 MSRP: $739.79
You Save: $188.65 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Sub-Assembly, Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Tail Pipe; Muffler & Pipe; Pipe Assembly, Exhaust, Center; Muffler
- Manufacturer Note: CALIFORNIA SPEC
- Position: Center
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1999-2002 Toyota 4Runner | Base, Limited, SR5 | 6 Cyl 3.4 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-31A10
$987.33 MSRP: $1325.28
You Save: $337.95 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Rear Right, Right; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010-2012 Toyota 4Runner | Limited, SR5, Trail | 6 Cyl 4.0 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-75631
$2673.14 MSRP: $3588.13
You Save: $914.99 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota 4Runner | SR5 | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-31450
$1197.53 MSRP: $1607.43
You Save: $409.90 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Rear Right, Right; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front; Catalytic Converter
- Manufacturer Note: *114=TOYOTA/T37/Y
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2009 Toyota 4Runner | Limited, Sport, SR5 | 6 Cyl 4.0 L GAS
View related parts
Toyota 4Runner Center Pipe
Part Number: 17420-75590
$448.20 MSRP: $601.61
You Save: $153.41 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler; Exhaust Pipe; Muffler; Pipe Assembly, Exhaust, Center
- Position: Center
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2010 Toyota 4Runner | SR5 | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Front Pipe, Driver Side
Part Number: 17450-31320
$972.91 MSRP: $1305.93
You Save: $333.02 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter, Left; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2023 Toyota 4Runner | 40th Anniversary Edition, Limited, Nightshade, SR5, SR5 Premium, Trail, TRD Off-Road, TRD Off-Road Premium, TRD Pro, TRD Sport, Venture | 6 Cyl 4.0 L GAS
View related parts
Toyota 4Runner Muffler & Tail Pipe, Center
Part Number: 17420-75080
$467.54 MSRP: $627.57
You Save: $160.03 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler; Exhaust Pipe; Tail Pipe; Muffler & Pipe; Pipe Assembly, Exhaust, Center; Muffler
- Position: Center
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1996-2000 Toyota 4Runner | Base | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Catalytic Converter, Front
Part Number: 17410-50360
$1440.30 MSRP: $1933.31
You Save: $493.01 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe; Front Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2004 Toyota 4Runner | Limited, Sport, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-31M90
$954.30 MSRP: $1280.94
You Save: $326.64 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Right; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2020-2023 Toyota 4Runner | 40th Anniversary Edition, Limited, Nightshade, SR5, SR5 Premium, Trail, TRD Off-Road, TRD Off-Road Premium, TRD Pro, TRD Sport, Venture | 6 Cyl 4.0 L GAS
View related parts
Toyota 4Runner Pipe Assembly, Exhaust, Front, Driver Side
Part Number: 17450-50120
$694.28 MSRP: $931.92
You Save: $237.64 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Catalytic Converter; Exhaust Pipe
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005 Toyota 4Runner | Limited, Sport, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-65090
$285.39 MSRP: $373.21
You Save: $87.82 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Manufacturer Note: CALIFORNIA SPEC
- Position: Front
- Replaces: 17410-65080
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1994-1995 Toyota 4Runner | SR5 | 6 Cyl 3.0 L GAS
View related parts
Toyota 4Runner Muffler & Tail Pipe
Part Number: 17405-75200
$242.19 MSRP: $316.72
You Save: $74.53 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Sub-Assembly, Exhaust; Exhaust Tail Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler; Tailpipe; Pipe Assembly, Exhaust, Tail; Tail Pipe
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1996-2000 Toyota 4Runner | Base | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Crossover Pipe, Front
Part Number: 17450-50090
$260.37 MSRP: $340.48
You Save: $80.11 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter; Exhaust Pipe; Front Pipe; Cross Over Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2003-2004 Toyota 4Runner | Limited, Sport, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota 4Runner Muffler & Tail Pipe, Center
Part Number: 17403-75030
Product Specifications
- Other Name: Pipe Sub-Assembly, Exhaust; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Tail Pipe; Muffler & Pipe; Pipe Assembly, Exhaust, Center; Muffler
- Position: Center
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1996-2000 Toyota 4Runner | Base | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-75260
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter; Exhaust Pipe; Converter & Pipe; Pipe Assembly, Exhaust, Front
- Manufacturer Note: CALIFORNIA SPEC
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000 Toyota 4Runner | Base | 4 Cyl 2.7 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-35210
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1989 Toyota 4Runner | DLX, SR5 | 4 Cyl 2.4 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-35420
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1985-1989 Toyota 4Runner | DLX, SR5 | 4 Cyl 2.4 L GAS
View related parts
Toyota 4Runner Front Pipe
Part Number: 17410-54390
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1986 Toyota 4Runner | DLX, SR5 | 4 Cyl 2.4 L GAS
View related parts
Toyota 4Runner Center Pipe
Part Number: 17420-63010
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Pipe
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1984-1990 Toyota 4Runner | DLX, SR5 | 4 Cyl 2.4 L GAS
View related parts
Toyota 4Runner Muffler & Tail Pipe
Part Number: 17430-YZZP8
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Tail Pipe; Muffler
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1991-1995 Toyota 4Runner | SR5 | 6 Cyl 3.0 L GAS

| Page 1 of 4 |Next >

1-20 of 65 Results

Toyota 4Runner Exhaust Pipe

Choose genuine Exhaust Pipe that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Exhaust Pipe for your Toyota 4Runner? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota 4Runner parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Toyota 4Runner Exhaust Pipe is an essential part of the car which makes a statement to intent, quality, and excellency of Toyota automobiles. Introduced to effectively channel out combustion products, the exhaust pipe ensures the dangerous products are channeled out of the cabin thus being very safe for the passengers. Made with strong alloys, the Toyota 4Runner Exhaust Pipe is specially designed to withstand tough and rough surfaces, thus, suitable for the 4Runner spirit of its owners. It fits different generations of this automobile, the fourth and the fifth generation 4Runner, the automobile features different powerful engines such as the 4.0 L V6 and 2.7 L inline 4-cylinder. This versatility returns the fact that the position of the exhaust pipe in improving the efficiency of an engine hence facilitating the performance of the Toyota 4Runner. However, the exhaust pipe has a succession of pipes whereby the gasses are streamlined hence improving the BHP of the engine through reduction of the back pressure. Toyota's 4Runner Exhaust Pipe is among the premier in the market for the car's construction and importantly for the job that it aids in within the Vehicle. Being one of the '10 Most Long-Lasting Cars,' the Toyota 4Runner proves that even the exhaust pipe is reliable, allowing every trip to be safe and efficient.

Toyota 4Runner Exhaust Pipe Parts and Q&A

Intermediate Pipe, Center
17420-50260
Q: How to install the exhaust pipe and its components on Toyota 4Runner?
A:
The installation of the exhaust pipe begins with attaching the heated oxygen sensor for Bank 2 to the exhaust pipe front while applying 44 Nm (450 kgf-cm, 33 ft-lbf) torque and connecting the sensor connector and inspecting the wire for twisting; re-install the sensor if twisting occurs. You must first apply the front pipe to the exhaust manifold after placing a new gasket and then tighten the exhaust pipe front with 2 nuts at 62 Nm (630 kgf-cm, 46 ft-lbf). Apply the same torque specifications while repeating the check on the wires for the heated oxygen sensor of Bank 1. To assembly the No. 2 exhaust front pipe you need two new gaskets and should install it to the exhaust manifold using 2 bolts and 2 nuts tightened to 62 Nm (630 kgf-cm, 46 ft-lbf) for the nuts and 48 Nm (490 kgf-cm, 35 ft-lbf) for the bolts. Proceed to measure the compression spring length with the vernier caliper before installation to validate its free length minimum requirement of 40.5 mm (4.5645 in.); replace the spring if it falls below this limit. Affix the exhaust pipe assembly front with new gasket and fasten 2 bolts and 2 springs through tightening them to 43 Nm (440 kgf-cm, 32 ft-lbf). A new gasket should be installed on the exhaust pipe center before attaching the tail pipe using 2 bolts torqued to 48 Nm (490 kgf-cm, 35 ft-lbf). Check for exhaust gas leaks.
Resonator & Pipe
17430-50220
Q: How to remove the exhaust pipe assembly on Toyota 4Runner?
A:
The first step for exhaust pipe assembly removal requires removing 2 bolts, exhaust pipe support along with tail pipe. Begin by removing the 2 bolts with their respective 2 compression springs and then proceed to the 4 exhaust pipe supports and exhaust pipe center. The assembly of the No. 2 exhaust front pipe requires removal of its two bolts and two nuts along with the entire assembly. The Bank 1 heated oxygen sensor connector needs disconnection while the heated oxygen sensor needs removal. Continue with the procedure by removing the exhaust pipe assembly front along with its installed 2 nuts. The removal process ends with removing the heated oxygen sensor after disconnecting its connector for Bank 2.