How to install the brake master cylinder without VSC on 2008 Toyota Tacoma?

The first step to install the brake master cylinder without VSC involves inspecting and adjusting the brake booster push rod through vacuum testing of the brake booster interior; stop the engine and use the brake pedal to remove air pressure until there are no signs of vacuum pressure. It is essential to adjust the booster push rod solely during new master cylinder replacements yet this procedure should be omitted when refitting an existing master cylinder to a new booster. Use Special Service Tool: 09737-00013 by setting it against the master cylinder before gradually lowering its pin toward the piston. Alternatively you can utilize Tool: 09737-00012. Set Special Service Tool: 09737-00013 upside down on the booster then use a ruler to check the booster push rod clearance against the pin head at 0 mm (0 in.). The rod clearance should be adjusted by using Special Service Tool: 09737-00020 to secure the rod while rotating the hexagon cap nut. Install a new brake master cylinder O-ring that needs to be secured through 2 brake booster nuts reaching a torque value of 13 Nm (127 kgf-cm, 9 ft-lbf). Use a union nut wrench to tighten the brake lines onto the master cylinder with 15 Nm (155 kgf cm or 11 ft-lbf) torque when not using the wrench or achieve 14 Nm (145 kgf cm or 10 ft-lbf) with the wrench while maintaining its parallel position to the nut. When working with manual transmission users should link the clutch reservoir tube to the tank followed by connecting the brake fluid level warning switch to the brake master cylinder. Add brake fluid to the reservoir before you perform a bleed of both master cylinder and brake line and verify the reservoir fluid level and check for leakages. To complete the inspection examine the brake pedal attributes including height position and freedom of movement alongside cable wire installation onto the negative battery fastener while tightening with 3.9 Nm torque force (40 kgf-cm, 35 in-lbf).

OEM 2008 Toyota Tacoma Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Brake Master Cylinders found

View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47028-04040
$292.64 MSRP: $417.82
You Save: $125.18 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master W/Plate
- Part Name Code: 47028
- Item Weight: 2.40 Pounds
- Item Dimensions: 10.1 x 7.7 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47028-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47028-04030
$246.04 MSRP: $351.28
You Save: $105.24 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master W/Plate
- Manufacturer Note: MEXICO SPEC(W/O (VSC, SIDE & *CUSA))
- Part Name Code: 47028
- Item Weight: 2.40 Pounds
- Item Dimensions: 12.2 x 7.4 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47028-04030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47025-04040
$1256.76 MSRP: $1841.79
You Save: $585.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: VSC-WITH(W/AUTO LSD)
- Part Name Code: 47201
- Item Weight: 2.10 Pounds
- Item Dimensions: 11.6 x 3.8 x 3.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47025-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47025-04020
$1256.76 MSRP: $1841.79
You Save: $585.03 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: VSC-WITH(W/AUTO LSD)
- Part Name Code: 47201
- Item Weight: 2.10 Pounds
- Item Dimensions: 11.4 x 3.7 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47025-04020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47025-04031
$1191.61 MSRP: $1500.00
You Save: $308.39 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: VSC-WITH(W/AUTO LSD & OFF SW)
- Part Name Code: 47201
- Item Weight: 2.10 Pounds
- Item Dimensions: 11.6 x 3.8 x 3.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47025-04031
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47050-04041
$1691.82 MSRP: $2479.38
You Save: $787.56 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Master Cylinder; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: VSC-WITH(W/AUTO LSD & OFF SW)
- Part Name Code: 47210L
- Item Weight: 2.40 Pounds
- Item Dimensions: 10.3 x 7.7 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47050-04041
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner | 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47050-04031
$1691.46 MSRP: $2478.85
You Save: $787.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Brake Booster; Brake Master Cylinder; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: VSC-WITH(W/AUTO LSD & OFF SW)
- Part Name Code: 47210L
- Item Weight: 8.20 Pounds
- Item Dimensions: 16.1 x 12.4 x 12.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47050-04031
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47050-04021
$1691.46 MSRP: $2478.85
You Save: $787.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Brake Booster; Brake Master Cylinder; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: VSC-WITH(W/AUTO LSD & OFF SW)
- Part Name Code: 47210L
- Item Weight: 8.80 Pounds
- Item Dimensions: 15.8 x 12.5 x 12.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47050-04021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner | 4 Cyl 2.7 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47025-04050
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Part Name Code: 47201
- Item Weight: 7.70 Pounds
- Item Dimensions: 21.2 x 12.6 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47025-04050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47025-04030
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: VSC-WITH(W/AUTO LSD)
- Part Name Code: 47201
- Item Weight: 4.00 Pounds
- Item Dimensions: 8.9 x 7.1 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47025-04030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2008 Toyota Tacoma Master Cylinder
Part Number: 47050-04051
Product Specifications
- Other Name: Cylinder Assembly, Brake; Power Brake Booster; Brake Master Cylinder; Brake Booster Assembly, W/Master Cylinder
- Part Name Code: 47210L
- Item Weight: 8.30 Pounds
- Item Dimensions: 15.7 x 12.7 x 12.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 47050-04051
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Tacoma Submodels:
- Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS

2008 Toyota Tacoma Brake Master Cylinder

Looking for affordable OEM 2008 Toyota Tacoma Brake Master Cylinder? Explore our comprehensive catalogue of genuine 2008 Toyota Tacoma Brake Master Cylinder. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Tacoma Parts Questions & Experts Answers

Q: How to install the brake master cylinder without VSC on 2008 Toyota Tacoma?
A: The first step to install the brake master cylinder without VSC involves inspecting and adjusting the brake booster push rod through vacuum testing of the brake booster interior; stop the engine and use the brake pedal to remove air pressure until there are no signs of vacuum pressure. It is essential to adjust the booster push rod solely during new master cylinder replacements yet this procedure should be omitted when refitting an existing master cylinder to a new booster. Use Special Service Tool: 09737-00013 by setting it against the master cylinder before gradually lowering its pin toward the piston. Alternatively you can utilize Tool: 09737-00012. Set Special Service Tool: 09737-00013 upside down on the booster then use a ruler to check the booster push rod clearance against the pin head at 0 mm (0 in.). The rod clearance should be adjusted by using Special Service Tool: 09737-00020 to secure the rod while rotating the hexagon cap nut. Install a new brake master cylinder O-ring that needs to be secured through 2 brake booster nuts reaching a torque value of 13 Nm (127 kgf-cm, 9 ft-lbf). Use a union nut wrench to tighten the brake lines onto the master cylinder with 15 Nm (155 kgf cm or 11 ft-lbf) torque when not using the wrench or achieve 14 Nm (145 kgf cm or 10 ft-lbf) with the wrench while maintaining its parallel position to the nut. When working with manual transmission users should link the clutch reservoir tube to the tank followed by connecting the brake fluid level warning switch to the brake master cylinder. Add brake fluid to the reservoir before you perform a bleed of both master cylinder and brake line and verify the reservoir fluid level and check for leakages. To complete the inspection examine the brake pedal attributes including height position and freedom of movement alongside cable wire installation onto the negative battery fastener while tightening with 3.9 Nm torque force (40 kgf-cm, 35 in-lbf).

Related 2008 Toyota Tacoma Parts

Alternate Year Models

2007 Toyota Tacoma Brake Master Cylinder 2009 Toyota Tacoma Brake Master Cylinder