How to install the brake master cylinder without VSC on Toyota Tacoma?

The first step to install the brake master cylinder without VSC involves inspecting and adjusting the brake booster push rod through vacuum testing of the brake booster interior; stop the engine and use the brake pedal to remove air pressure until there are no signs of vacuum pressure. It is essential to adjust the booster push rod solely during new master cylinder replacements yet this procedure should be omitted when refitting an existing master cylinder to a new booster. Use Special Service Tool: 09737-00013 by setting it against the master cylinder before gradually lowering its pin toward the piston. Alternatively you can utilize Tool: 09737-00012. Set Special Service Tool: 09737-00013 upside down on the booster then use a ruler to check the booster push rod clearance against the pin head at 0 mm (0 in.). The rod clearance should be adjusted by using Special Service Tool: 09737-00020 to secure the rod while rotating the hexagon cap nut. Install a new brake master cylinder O-ring that needs to be secured through 2 brake booster nuts reaching a torque value of 13 Nm (127 kgf-cm, 9 ft-lbf). Use a union nut wrench to tighten the brake lines onto the master cylinder with 15 Nm (155 kgf cm or 11 ft-lbf) torque when not using the wrench or achieve 14 Nm (145 kgf cm or 10 ft-lbf) with the wrench while maintaining its parallel position to the nut. When working with manual transmission users should link the clutch reservoir tube to the tank followed by connecting the brake fluid level warning switch to the brake master cylinder. Add brake fluid to the reservoir before you perform a bleed of both master cylinder and brake line and verify the reservoir fluid level and check for leakages. To complete the inspection examine the brake pedal attributes including height position and freedom of movement alongside cable wire installation onto the negative battery fastener while tightening with 3.9 Nm torque force (40 kgf-cm, 35 in-lbf).

How to remove and replace the brake master cylinder on Toyota Tacoma?

The brake master cylinder replacement starts with pumping the brake pedal multiple times to vent vacuum from the booster before disconnecting the battery's negative cable and draining the fluid. Then immediately cleanse any touched paint with solvent. The clutch reservoir tube needs to be separated from the reservoir system of manual transmission vehicles before any work can proceed. First disconnect the brake fluid level warning switch connector followed by using a union nut wrench to separate the 2 brake lines from the brake master cylinder sub-assembly, remove the 2 nuts, then extract the brake master cylinder sub-assembly from the brake booster with caution to preserve the O-ring. Keep the master cylinder out of harm to protect its usefulness because a dropped master cylinder cannot be put back into use. Keep the pressure off the master cylinder piston while installation and removal of the sub-assembly by minimizing bending and positioning it horizontally or downward. This arrangement prevents piston detachment. Foreign objects should not come into contact with the master cylinder piston and in case of contamination a clean cloth should be used to remove the foreign matter followed by lithium soap-based glycol grease application around the circumference of the piston pnictle. Different types of grease or fluid must not be used during this process.

OEM Toyota Tacoma Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

55 Brake Master Cylinders found

View related parts
Toyota Tacoma Master Cylinder Part Number: 47028-04030
$253.49 MSRP: $361.93
You Save: $108.44 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master W/Plate
- Manufacturer Note: MEXICO SPEC(W/O (VSC, SIDE & *CUSA))
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2009 Toyota Tacoma | Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47201-04170
$130.06 MSRP: $184.12
You Save: $54.06 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Replaces: 47201-04150
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2009-2023 Toyota Tacoma | Base, Limited, Pre Runner, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47028-04040
$331.66 MSRP: $473.54
You Save: $141.88 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master W/Plate
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2009 Toyota Tacoma | Base, Pre Runner, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Booster Assembly Part Number: 47050-04180
$1433.15 MSRP: $2100.30
You Save: $667.15 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2023 Toyota Tacoma | Limited, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04210
$751.36 MSRP: $1101.12
You Save: $349.76 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Master Cylinder Assembly; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: OFF ROAD PACKAGE
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2023 Toyota Tacoma | Limited, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04055
$752.29 MSRP: $1102.49
You Save: $350.20 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04035
$848.59 MSRP: $1243.63
You Save: $395.04 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Cylinder Sub-Assembly, Brake Stroke Simulator Part Number: 47055-AK040
$907.42 MSRP: $1329.84
You Save: $422.42 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER SUB-ASSY, B
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2024-2025 Toyota Tacoma | Limited, SR, SR5, Trailhunter, TRD Off-Road, TRD PreRunner, TRD Pro, TRD Sport | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS
View related parts
Toyota Tacoma Cylinder Sub-Assembly, Brake Stroke Simulator Part Number: 47055-AK030
$907.42 MSRP: $1329.84
You Save: $422.42 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER SUB-ASSY, B
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2024-2025 Toyota Tacoma | Trailhunter | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Tacoma Cylinder Sub-Assembly, Brake Stroke Simulator Part Number: 47055-AK020
$907.41 MSRP: $1329.82
You Save: $422.41 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER SUB-ASSY, B
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2024-2025 Toyota Tacoma | Limited, SR, SR5, Trailhunter, TRD Off-Road, TRD PreRunner, TRD Pro, TRD Sport | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS
View related parts
Toyota Tacoma Cylinder Sub-Assembly, Brake Stroke Simulator Part Number: 47055-AK010
$907.42 MSRP: $1329.84
You Save: $422.42 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CYLINDER SUB-ASSY, B
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2024-2025 Toyota Tacoma | Limited, SR, SR5, Trailhunter, TRD Off-Road, TRD PreRunner, TRD Pro, TRD Sport | 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04054
$961.04 MSRP: $1408.41
You Save: $447.37 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: WITH(*FTP & *EUC:PNC51405A & 51406A)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04034
$961.04 MSRP: $1408.41
You Save: $447.37 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: WITH(*FTP & *EUC:PNC51405A & 51406A)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2012-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Booster Assembly Part Number: 47050-04035
$1043.29 MSRP: $1528.96
You Save: $485.67 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Assembly, Brake; Brake Booster; Brake Booster Assembly, W/Master Cylinder
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2013-2015 Toyota Tacoma | Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04190
$1166.43 MSRP: $1709.42
You Save: $542.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Master Cylinder Assembly; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2023 Toyota Tacoma | Limited, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04180
$1166.43 MSRP: $1709.42
You Save: $542.99 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Master Cylinder Assembly; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2018-2023 Toyota Tacoma | Limited, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47201-3D250
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: W(ABS)
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2000 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47201-04030
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2000 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47201-04060
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2004 Toyota Tacoma | Base, Pre Runner, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Master Cylinder Part Number: 47025-04050
Product Specifications
- Other Name: Cylinder Sub-Assembly; Brake Master Cylinder; Cylinder Sub-Assembly, Brake Master
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2009 Toyota Tacoma | Base, Pre Runner, X-Runner | 6 Cyl 4.0 L GAS

| Page 1 of 3 |Next >

1-20 of 55 Results

Toyota Tacoma Brake Master Cylinder

Choose genuine Brake Master Cylinder that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Master Cylinder for your Toyota Tacoma? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Tacoma parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

Brake Master Cylinder of the Toyota Tacoma cars is part of the brake system that translates the foot force applied to hydraulic pressure to operate the slave cylinders. This system hydraulically transmits force form the master cylinder piston to slave cylinders; it increases both force and displacement. Most Toyota Tacoma have a dual circuit master cylinder with two pistons, thus even if one hydraulic circuit is non-functional, the second one would provide enough pressure to stop the vehicle. It engages the calipers or the drum brakes to produce friction to lock the wheels; besides, it actuates the slave cylinder that releases the clutch. Altogether, Brake Master Cylinder is vital in the optimum and flawless functionality of the brake and clutch systems due to the proper control of hydraulic force and pressure.

Toyota Tacoma Brake Master Cylinder Parts and Q&A

Master Cylinder
47028-04040
Q: How to install the brake master cylinder without VSC on Toyota Tacoma?
A:
The first step to install the brake master cylinder without VSC involves inspecting and adjusting the Brake Booster push rod through vacuum testing of the brake booster interior; stop the engine and use the brake pedal to remove air pressure until there are no signs of vacuum pressure. It is essential to adjust the booster push rod solely during new master cylinder replacements yet this procedure should be omitted when refitting an existing master cylinder to a new booster. Use Special Service Tool: 09737-00013 by setting it against the master cylinder before gradually lowering its pin toward the piston. Alternatively you can utilize Tool: 09737-00012. Set Special Service Tool: 09737-00013 upside down on the booster then use a ruler to check the booster push rod clearance against the pin head at 0 mm (0 in.). The rod clearance should be adjusted by using Special Service Tool: 09737-00020 to secure the rod while rotating the hexagon cap nut. Install a new brake master cylinder O-ring that needs to be secured through 2 brake booster nuts reaching a torque value of 13 Nm (127 kgf-cm, 9 ft-lbf). Use a union nut wrench to tighten the brake lines onto the master cylinder with 15 Nm (155 kgf cm or 11 ft-lbf) torque when not using the wrench or achieve 14 Nm (145 kgf cm or 10 ft-lbf) with the wrench while maintaining its parallel position to the nut. When working with manual transmission users should link the clutch reservoir tube to the tank followed by connecting the brake fluid level warning switch to the brake master cylinder. Add brake fluid to the reservoir before you perform a bleed of both master cylinder and brake line and verify the reservoir fluid level and check for leakages. To complete the inspection examine the brake pedal attributes including height position and freedom of movement alongside cable wire installation onto the negative battery fastener while tightening with 3.9 Nm torque force (40 kgf-cm, 35 in-lbf).
Master Cylinder
47028-04030
Q: How to remove and replace the brake master cylinder on Toyota Tacoma?
A:
The brake master cylinder replacement starts with pumping the brake pedal multiple times to vent vacuum from the booster before disconnecting the battery's negative cable and draining the fluid. Then immediately cleanse any touched paint with solvent. The clutch reservoir tube needs to be separated from the reservoir system of manual transmission vehicles before any work can proceed. First disconnect the brake fluid level warning switch connector followed by using a union nut wrench to separate the 2 brake lines from the brake master cylinder sub-assembly, remove the 2 nuts, then extract the brake master cylinder sub-assembly from the Brake Booster with caution to preserve the O-ring. Keep the master cylinder out of harm to protect its usefulness because a dropped master cylinder cannot be put back into use. Keep the pressure off the master cylinder piston while installation and removal of the sub-assembly by minimizing bending and positioning it horizontally or downward. This arrangement prevents piston detachment. Foreign objects should not come into contact with the master cylinder piston and in case of contamination a clean cloth should be used to remove the foreign matter followed by lithium soap-based glycol grease application around the circumference of the piston pnictle. Different types of grease or fluid must not be used during this process.