How to install the exhaust pipe and its components on 2008 Toyota Sequoia?

The installation of the exhaust pipe begins by installing the 4 converter protector stays and monolithic converter protector with 4 bolts and 4 nuts torque to 11 Nm (107 kgf-cm, 8 ft-lbf) while maintaining the protector within the specified angle range. The configuration of heated oxygen sensor for Bank 1 Sensor 2 requires Special Service Tool: 09224-00010 and a torque magnification of 40 Nm (408 kgf-cm, 30 ft-lbf) when using the tool or 44 Nm (449 kgf-cm, 33 ft-lbf) without with a torque wrench fitted at a fulcrum length of 300 cm (11.8 in.). The installation procedure using Special Service Tool 09224-00010 should be repeated for the Bank 1 Sensor 1 air fuel ratio sensor. Position the new gasket on the front No. 2 exhaust pipe assembly before installing three new nuts with torque specifications at 54 Nm (554 kgf-cm, 40 ft-lbf). Then connect each of the heated oxygen sensor and air fuel ratio sensor connectors. The No. 1 monolithic converter protector must use four bolts and four nuts with a torque setting of 11 Nm (107 kgf-cm, 8 ft-lbf). The front No. 3 exhaust pipe sub-assembly can be installed using two bolts combined with two nuts which should be torqued to 48 Nm (489 kgf-cm, 35 ft-lbf). The installation of the No. 1 monolithic converter protector should be performed exactly like before. The installation of the heated oxygen sensor for Bank 2 Sensor 2 requires Special Service Tool: 09224-00010, which should be torqued according to the previous specifications. Perform the same installation method for the air fuel ratio sensor which belongs to Bank 2 Sensor 1. Install a new gasket onto the front exhaust pipe assembly while fixing it with 3 new nuts and torquing them to 40 ft-lbf (40 ft-lbf, 40 ft-lbf). Afterward connect the sensor connectors. The center exhaust pipe assembly requires two new gaskets during installation while its connection to three pipe supports should be done through four bolts torqued up to 48 Nm (489 kgf-cm, 35 ft-lbf). Use a new clutch gasket to connect the tail exhaust pipe assembly while maintaining a clamp torque force to 32 Nm (326 kgf-cm, 24 ft-lbf) with correct clamp orientation and examine for exhaust gas leaks.

OEM 2008 Toyota Sequoia Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Exhaust Pipes found

View related parts
2008 Toyota Sequoia Front Pipe
Part Number: 17410-0S011
$1746.73 MSRP: $2344.62
You Save: $597.89 (26%)
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Right; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Replaces: 17410-0S010
- Part Name Code: 17410
- Item Weight: 11.00 Pounds
- Item Dimensions: 48.6 x 18.4 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-0S011
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Front Pipe
Part Number: 17410-0S070
$1589.59 MSRP: $2133.69
You Save: $544.10 (26%)
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Right; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Part Name Code: 17410
- Item Weight: 13.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-0S070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Tail Pipe
Part Number: 17430-0S021
$272.20 MSRP: $355.97
You Save: $83.77 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Tail; Exhaust Tail Pipe; Exhaust Pipe; Tailpipe; Pipe Assembly, Exhaust, Tail
- Replaces: 17430-0S020
- Part Name Code: 17430
- Item Weight: 11.00 Pounds
- Item Dimensions: 44.4 x 12.3 x 9.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17430-0S021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Front Pipe, Driver Side
Part Number: 17450-0S140
$1846.72 MSRP: $2478.84
You Save: $632.12 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter, Left; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front Driver Side
- Replaces: 17450-0S011, 17450-0S010
- Part Name Code: 17450B
- Item Weight: 6.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17450-0S140
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Platinum, SR5 | 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
2008 Toyota Sequoia Tail Pipe
Part Number: 17430-0F020
$295.25 MSRP: $386.10
You Save: $90.85 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Tail; Exhaust Tail Pipe; Exhaust Pipe; Tailpipe; Pipe Assembly, Exhaust, Tail
- Part Name Code: 17430
- Item Weight: 11.00 Pounds
- Item Dimensions: 44.4 x 12.8 x 8.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17430-0F020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2008 Toyota Sequoia Front Pipe, Driver Side
Part Number: 17450-0F120
$1849.49 MSRP: $2482.55
You Save: $633.06 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust Front; Catalytic Converter, Left; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front Driver Side
- Part Name Code: 17450B
- Item Weight: 11.20 Pounds
- Item Dimensions: 40.8 x 14.4 x 8.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17450-0F120
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2008 Toyota Sequoia Front Pipe
Part Number: 17410-0F090
$1934.46 MSRP: $2596.61
You Save: $662.15 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Catalytic Converter, Right; Exhaust Pipe; Pipe Assembly, Exhaust, Front
- Position: Front
- Part Name Code: 17410
- Item Weight: 11.00 Pounds
- Item Dimensions: 48.6 x 17.7 x 9.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17410-0F090
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2008 Toyota Sequoia Muffler & Pipe, Center
Part Number: 17420-0F060
$417.33 MSRP: $560.18
You Save: $142.85 (26%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler; Exhaust Pipe; Tail Pipe; Muffler; Pipe Assembly, Exhaust, Center
- Position: Center
- Part Name Code: 17420
- Item Weight: 16.60 Pounds
- Item Dimensions: 51.9 x 19.6 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-0F060
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2008 Toyota Sequoia Muffler & Pipe, Center
Part Number: 17420-0S040
$485.17 MSRP: $651.24
You Save: $166.07 (26%)
Product Specifications
- Other Name: Pipe Assembly, Exhaust; Exhaust Muffler; Exhaust Pipe; Tail Pipe; Muffler; Pipe Assembly, Exhaust, Center
- Position: Center
- Part Name Code: 17420
- Item Weight: 17.20 Pounds
- Item Dimensions: 50.9 x 20.0 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 17420-0S040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Sequoia Submodels:
- Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS

2008 Toyota Sequoia Exhaust Pipe

Looking for affordable OEM 2008 Toyota Sequoia Exhaust Pipe? Explore our comprehensive catalogue of genuine 2008 Toyota Sequoia Exhaust Pipe. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Sequoia Parts Questions & Experts Answers

Q: How to install the exhaust pipe and its components on 2008 Toyota Sequoia?
A: The installation of the exhaust pipe begins by installing the 4 converter protector stays and monolithic converter protector with 4 bolts and 4 nuts torque to 11 Nm (107 kgf-cm, 8 ft-lbf) while maintaining the protector within the specified angle range. The configuration of heated oxygen sensor for Bank 1 Sensor 2 requires Special Service Tool: 09224-00010 and a torque magnification of 40 Nm (408 kgf-cm, 30 ft-lbf) when using the tool or 44 Nm (449 kgf-cm, 33 ft-lbf) without with a torque wrench fitted at a fulcrum length of 300 cm (11.8 in.). The installation procedure using Special Service Tool 09224-00010 should be repeated for the Bank 1 Sensor 1 air fuel ratio sensor. Position the new gasket on the front No. 2 exhaust pipe assembly before installing three new nuts with torque specifications at 54 Nm (554 kgf-cm, 40 ft-lbf). Then connect each of the heated oxygen sensor and air fuel ratio sensor connectors. The No. 1 monolithic converter protector must use four bolts and four nuts with a torque setting of 11 Nm (107 kgf-cm, 8 ft-lbf). The front No. 3 exhaust pipe sub-assembly can be installed using two bolts combined with two nuts which should be torqued to 48 Nm (489 kgf-cm, 35 ft-lbf). The installation of the No. 1 monolithic converter protector should be performed exactly like before. The installation of the heated oxygen sensor for Bank 2 Sensor 2 requires Special Service Tool: 09224-00010, which should be torqued according to the previous specifications. Perform the same installation method for the air fuel ratio sensor which belongs to Bank 2 Sensor 1. Install a new gasket onto the front exhaust pipe assembly while fixing it with 3 new nuts and torquing them to 40 ft-lbf (40 ft-lbf, 40 ft-lbf). Afterward connect the sensor connectors. The center exhaust pipe assembly requires two new gaskets during installation while its connection to three pipe supports should be done through four bolts torqued up to 48 Nm (489 kgf-cm, 35 ft-lbf). Use a new clutch gasket to connect the tail exhaust pipe assembly while maintaining a clamp torque force to 32 Nm (326 kgf-cm, 24 ft-lbf) with correct clamp orientation and examine for exhaust gas leaks.

Related 2008 Toyota Sequoia Parts

Alternate Year Models

2007 Toyota Sequoia Exhaust Pipe 2009 Toyota Sequoia Exhaust Pipe