Other Name: Motor Assembly, Rear Wiper; Back Glass Wiper Motor; Rear Motor
Manufacturer Note: BACK GLASS-WITH(GLASS HATCH-BACK DOOR)
Position: Rear
Replaces: 85130-0E050, 85130-48040
Part Name Code: 85110R
Item Weight: 1.40 Pounds
Item Dimensions: 12.4 x 10.6 x 8.1 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 85130-0E051
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
Other Name: Motor Assembly, Rear Wiper; Back Glass Wiper Motor; Rear Motor
Position: Rear
Part Name Code: 85110R
Item Weight: 2.60 Pounds
Item Dimensions: 9.7 x 5.6 x 4.9 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 85130-48050
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
Base, Hybrid, Hybrid Limited, Limited, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
2008 Toyota Highlander Wiper Motor
Looking for affordable OEM 2008 Toyota Highlander Wiper Motor? Explore our comprehensive catalogue of genuine 2008 Toyota Highlander Wiper Motor. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2008 Toyota Highlander Wiper Motor Parts Q&A
Q: How to install the windshield wiper motor assembly and related components on 2008 Toyota Highlander?
A: Install windshield wiper motor with 3 bolts (torque 5.4 Nm) before engaging the clamp, matching parts, and setting the crank arm assembly using 17 Nm. Apply MP grease to the crank arm and link rod joint. Use MP grease to lubricate the crank arm pivot and attach the rod of the wiper link assembly to it. Place the windshield wiper motor and link assembly on 4 bolts then tighten to 7.0 Nm while connecting the connector. Press the 20 holding claws into the cowl top ventilator louver sub-assembly openings and secure with 2 clips. Seam the front fender to cowl side seals LH and RH by inserting two claws each. Press the eight clips to fix the hood to cowl top seal. To install the RH front wiper arm and blade properly you should operate the wiper to reach automatic stop position before cleaning arm surfaces and pivots for assembly installation with the nut tightened to 24 Nm while holding the arm by hand during torque. Follow this step with the left-hand wiper components to verify proper operation of both wipers during washer fluid distribution on the windshield screen.