How to service and repair the front upper Control Arm on 2006 Toyota Tacoma?

Service and repair processes for the front upper suspension arm should start by disconnecting the negative battery terminal cable and removing the front wheel. Checking for ball joint slab in the front suspension upper arm requires a shaking motion up and down. The skid control sensor wire needs separating by disconnecting both the speed sensor connector and removing the two bolts. You should untighten the bolt that attaches the front flexible hose. The front suspension lower arm must be supported by a jack while the nut and clip are removed along with the use of Special Service Tool: 09628-62011 to detach the upper ball joint from the steering knuckle before unfastening the 2 bolts and the front suspension upper arm. Disassembly of the front suspension upper arm bush begins when you elevate its bushing flange section using a chisel and hammer before installing Special Service Tool: 09950-40011 (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011), 09950-60010, 09951-00380 to extract the upper arm bush. The same burin procedure works for the opposite side. Inspect the ball joint dust cover after rotating its stud five times back and forth using a torque wrench on the nut to 4.5 Nm (46 kgf-cm, 40 inch lbs.) or less, while assessing for any dust cover cracks or grease leakage during this inspection. To reassemble the unit install a new upper arm bush with the combination of Special Service Tools: 09631-20081, 09710-04081 and a press following techniques for the rear side. Install the front suspension upper arm along with 2 bolts yet maintain the assembly by torquing to 110 Nm (1,122 kgf-cm, 81 ft. lbs.). Next step, apply a new nut and clip. Secure the front flexible hose with its bolt at 32 Nm while installing the skid control sensor wire using two bolts to 5.0 Nm before connecting the speed sensor connector. Insert the front wheel and tighten the bolts to 113 Nm (1,152 kgf-cm, 83 ft. lbs.), proceed to lower the vehicle, then perform multiple suspension stability tests by bouncing the vehicle. The front suspension upper arm bolts require a torque of 82 Nm (836kgf cm, 60 ft lbs) tightening before connector the cable to the negative terminal using 3.9 Nm (40 kgf cm, 35 inch lbs). A wheel alignment check is necessary after this procedure.

OEM 2006 Toyota Tacoma Control Arm

Suspension Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Control Arms found

View related parts
2006 Toyota Tacoma Upper Control Arm, Driver Side
Part Number: 48630-04021
$284.98 MSRP: $406.89
You Save: $121.91 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly, Suspension; Suspension Control Arm, Front Left Upper; Control Arm Assembly; Arm Assembly, Front Suspension, Upper Driver Side; Control Arm
- Position: Upper Driver Side
- Replaces: 48630-04020
- Part Name Code: 48630
- Item Weight: 7.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48630-04021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Limited, Nightshade, Pre Runner, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Upper Control Arm, Passenger Side
Part Number: 48610-04021
$284.98 MSRP: $406.89
You Save: $121.91 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly, Suspension; Suspension Control Arm, Front Right Upper; Control Arm Assembly; Arm Assembly, Front Suspension Upper, Passenger Side; Control Arm
- Position: Passenger Side
- Replaces: 48610-04020
- Part Name Code: 48610
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48610-04021
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Limited, Nightshade, Pre Runner, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Lower Control Arm, Passenger Side
Part Number: 48068-04040
$283.88 MSRP: $405.30
You Save: $121.42 (30%)
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assembly, Suspension; Suspension Control Arm, Front Right Lower; Control Arm Assembly; Arm Sub-Assembly, Front Suspension, Lower Passenger Side; Control Arm
- Position: Passenger Side
- Part Name Code: 48068
- Item Weight: 70.90 Pounds
- Item Dimensions: 47.7 x 35.4 x 30.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48068-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Lower Control Arm, Driver Side
Part Number: 48069-04040
$272.14 MSRP: $388.55
You Save: $116.41 (30%)
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assembly, Suspension; Suspension Control Arm, Front Left Lower; Control Arm Assembly; Arm Sub-Assembly, Front Suspension, Lower Driver Side; Control Arm
- Position: Lower Driver Side
- Replaces: 48069-04050
- Part Name Code: 48069
- Item Weight: 72.20 Pounds
- Item Dimensions: 46.4 x 35.4 x 30.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48069-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, Pre Runner, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Upper Control Arm, Driver Side
Part Number: 48630-04010
$282.86 MSRP: $403.87
You Save: $121.01 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly, Suspension; Suspension Control Arm, Front Left Upper; Control Arm Assembly; Arm Assembly, Front Suspension, Upper Driver Side; Control Arm
- Position: Upper Driver Side
- Part Name Code: 48630
- Item Weight: 7.10 Pounds
- Item Dimensions: 14.3 x 6.3 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48630-04010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Upper Control Arm, Passenger Side
Part Number: 48610-04010
$282.86 MSRP: $403.87
You Save: $121.01 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly, Suspension; Suspension Control Arm, Front Right Upper; Control Arm Assembly; Arm Assembly, Front Suspension Upper, Passenger Side; Control Arm
- Position: Passenger Side
- Part Name Code: 48610
- Item Weight: 9.20 Pounds
- Item Dimensions: 18.1 x 12.5 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48610-04010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Lower Control Arm, Driver Side
Part Number: 48069-04030
$246.19 MSRP: $351.50
You Save: $105.31 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assembly, Suspension; Suspension Control Arm, Front Left Lower; Control Arm Assembly; Arm Sub-Assembly, Front Suspension, Lower Driver Side; Control Arm
- Position: Lower Driver Side
- Part Name Code: 48069
- Item Weight: 19.70 Pounds
- Item Dimensions: 17.5 x 7.0 x 16.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48069-04030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS
View related parts
2006 Toyota Tacoma Lower Control Arm, Passenger Side
Part Number: 48068-04030
$246.19 MSRP: $351.50
You Save: $105.31 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Sub-Assembly, Suspension; Suspension Control Arm, Front Right Lower; Control Arm Assembly; Arm Sub-Assembly, Front Suspension, Lower Passenger Side; Control Arm
- Position: Passenger Side
- Part Name Code: 48068
- Item Weight: 20.40 Pounds
- Item Dimensions: 18.3 x 6.9 x 16.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 48068-04030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2006 Toyota Tacoma Submodels:
- Base, TRD Pro, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 4.0 L GAS

2006 Toyota Tacoma Control Arm

Looking for affordable OEM 2006 Toyota Tacoma Control Arm? Explore our comprehensive catalogue of genuine 2006 Toyota Tacoma Control Arm. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2006 Toyota Tacoma Parts Questions & Experts Answers

Q: How to service and repair the front upper Control Arm on 2006 Toyota Tacoma?
A: Service and repair processes for the front upper suspension arm should start by disconnecting the negative battery terminal cable and removing the front wheel. Checking for ball joint slab in the front suspension upper arm requires a shaking motion up and down. The skid control sensor wire needs separating by disconnecting both the speed sensor connector and removing the two bolts. You should untighten the bolt that attaches the front flexible hose. The front suspension lower arm must be supported by a jack while the nut and clip are removed along with the use of Special Service Tool: 09628-62011 to detach the upper ball joint from the steering knuckle before unfastening the 2 bolts and the front suspension upper arm. Disassembly of the front suspension upper arm bush begins when you elevate its bushing flange section using a chisel and hammer before installing Special Service Tool: 09950-40011 (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011), 09950-60010, 09951-00380 to extract the upper arm bush. The same burin procedure works for the opposite side. Inspect the ball joint dust cover after rotating its stud five times back and forth using a torque wrench on the nut to 4.5 Nm (46 kgf-cm, 40 inch lbs.) or less, while assessing for any dust cover cracks or grease leakage during this inspection. To reassemble the unit install a new upper arm bush with the combination of Special Service Tools: 09631-20081, 09710-04081 and a press following techniques for the rear side. Install the front suspension upper arm along with 2 bolts yet maintain the assembly by torquing to 110 Nm (1,122 kgf-cm, 81 ft. lbs.). Next step, apply a new nut and clip. Secure the front flexible hose with its bolt at 32 Nm while installing the skid control sensor wire using two bolts to 5.0 Nm before connecting the speed sensor connector. Insert the front wheel and tighten the bolts to 113 Nm (1,152 kgf-cm, 83 ft. lbs.), proceed to lower the vehicle, then perform multiple suspension stability tests by bouncing the vehicle. The front suspension upper arm bolts require a torque of 82 Nm (836kgf cm, 60 ft lbs) tightening before connector the cable to the negative terminal using 3.9 Nm (40 kgf cm, 35 inch lbs). A wheel alignment check is necessary after this procedure.

Related 2006 Toyota Tacoma Parts

Alternate Year Models

2005 Toyota Tacoma Control Arm 2007 Toyota Tacoma Control Arm