Toyota 84231-60070
Door Jamb Switch

The first task when servicing the front door courtesy switch requires disconnecting the negative cable from the battery while allowing 90 seconds for protection of Air Bags and seat belt pretensioner activation. Service of the front door courtesy switch begins with disassembling its assembly by taking out the bolt and switch and disconnecting the connector. The installation involves joining the connector followed by installing the switch together with the bolt. After disconnecting the cable from the negative terminal users need to schedule initialization because specific systems demand an initialization process after reconnecting it.

A correct service procedure for the back door courtesy switch requires users to disconnect the cable from the negative terminal and let it sit for 90 seconds or more to prevent Air Bag and seat belt pretensioners from activating. Service of the back door courtesy switch begins by uninstalling the back door garnish center and both back door side garnish LH and RH and the back door trim board assembly and back door lock assembly. Begin installation by attaching the back door lock assembly and then install the back door trim board assembly followed by back door side garnish RH and then back door side garnish LH and conclude with back door garnish center. The procedure ends by reconnecting the cable to the negative terminal while completing the system initialization process that some features need following cable removal.

The first task when servicing the lower side rear door courtesy switch involves disconnecting the negative battery cable. Service the rear door courtesy switch for the lower side by removing first the access panel rear Weather Strip and then the lap belt outer anchor cover and finally the rear door inside handle subassembly along with the No. 1 cup holder and rear door trim board subassembly. Start by disconnecting the connector and connector clamp along with the access panel lock control cable from the lower assembly before loosening the three screws with a Torx T30 wrench socket to push the access panel lock upward. Begin the installation process by mounting the access panel lower lock assembly onto the rear door withstarter torque of 5.0 N.m (51 kgf.cm, 44 in.lbf) then reconnect all wiring components including the connector the connector clamp and access panel lock control cable. Next install the rear door trim surface board assembly as well as the No. 1 cup holder and rear door internal handle assembly followed by lap belt outer fixture sheet then position the access panel rear seal. The negative battery terminal needs cable attachment while using 3.9 N.m (40 kgf.cm, 35 in.lbf) torque.

The service for back door courtesy switch begins with negative battery cable removal to maintain at least 90 seconds of continuous wait before Air Bags and seat belt pretensioner activation. First break open the back door courtesy light switch assembly by unscrewing the switch and bolt while disconnecting its connector. The back door courtesy switch service requires the same installation process for RH and LH sides with a specific note that following steps pertain to the LH side. Apply the connector first before installing the switch by using the bolt. The last step is reconnecting the cable to the negative terminal.

Dismantling the negative battery terminal cable is the first step in servicing the Front Door Courtesy Switch yet the installer must wait 90 seconds to stop the deployment of Air Bags and seat belt pretensioners. The service begins with removing the Front Door Courtesy Light Switch Assembly by unfastening the bolt and switch before disconnecting the connector. The connector assembly installation requires first connecting the components followed by switch installation with the bolt that lacks torque requirements. Reinstall the cable to the negative battery terminal as the last step. The installation process must be applied identically to the RH and LH sides.

Before servicing the front door courtesy switch the technician must disconnect the negative cable from the battery terminal while waiting for 90 seconds to avoid Air Bag and seat belt pretensioner activation. The first procedure involves unbolted the front door courtesy light switch assembly while disconnecting both the bolt and switch and the connector. A user must first join the cable and afterward must fasten the switch using the bolt for installation. The initialization process must occur after reconnecting the cable to the negative battery terminal since system requirements need it when disconnecting and reconnecting the cable.

Ensure a torque of 12 N.m (122 kgf.cm, 8.9 ft.lbf) is applied.

Connect the connector and use the "TORX" socket wrench (T30) to secure the assembly with the "TORX" bolt.

Disconnect the connector, harness clamp, and access panel lock control cable, then remove the three bolts securing the lock.

Disconnect the cable from the negative battery terminal and wait at least 90 seconds to prevent airbag and seat belt pretensioner activation.

Disconnect the cable from the negative battery terminal and wait at least 90 seconds to prevent airbag and seat belt pretensioner activation.

First, disconnect the cable from the negative battery terminal and wait at least 90 seconds to prevent airbag and seat belt pretensioner activation.

Connect the connector and install the switch with the bolt, which does not have a specified torque.