Toyota 90915-YZZN1
Oil Filter

Before changing the oil filter you must wear protective clothing and gloves together with mineral oil skin protection to reduce its irritative effects but remember to follow the correct waste disposal procedures. Start the replacement process by draining your engine oil by removing the oil fill cap. Afterward uninstall the oil drain plug to collect the oil in a suitable container. Begin the oil filter replacement through the removal process by employing Special Service Tool: 09228-06501. Wash the area for installing the new oil filter and lubricate the filter gasket using fresh engine oil. Begin by hand-tightening the oil filter into position until the gasket rencontre(itemizes) the seat while using Special Service Tool: 09228-06501 before advancing to the full tightening process with the same tool. A torque wrench can be used for oil filter tightening to 17.2 Nm (175 kgf-cm, 13 ft. lbs.); otherwise, a common wrench or hand tightening it 3/4 turn works instead. Although it's difficult to miss the oil drain plug after draining the oil, you must cleanse and install the plug using a new gasket which needs to be tightened to 37.5 Nm (382 kgf-cm, 28 ft. lbs.) while re-filling the engine with standard oil before securing the oil filler cap. Inspect for present oil leakages from the engine.

Exchange of the oil filter sub-assembly requires you to protect yourself against engine oil exposure since regular contact can lead to skin reactions and dermatitis and the oil carries dangerous substances. Protect your hands and skin by wearing appropriate clothing and gloves and either wash the affected area with water and soap or utilize water-free hand cleaner if you encounter used oil. The usage of gasoline or thinners or solvents is prohibited for this purpose. The proper disposal sites exist for recycling used oil and oil filters. Begin the procedure by draining engine oil followed by using Special Service Tool: 09228-06501 to remove the oil filter. The surface for the new oil filter installation should be cleaned and you should apply fresh engine oil to its gasket. Position the new oil filter lightly then tighten it just enough for the gasket to touch its seat before using Special Service Tool: 09228-06501 to reach an additional 3/4 turn. The oil pan drain plug installation requires a new gasket and torqued to a torque value of 38 Nm (382 kgf-cm, 28 ft. lbs.). Engine oil must be added to reach a volume of 3.7 liters (3.9 US qts, 3.3 Imp. qts) when installing an oil filter but only 3.4 liters (3.6 US qts, 3.0 Imp. qts) without filter. The tank will require 4.1 liters (4.3 US qts, 3.6 Imp. qts) to achieve a dry fill condition. Do one more check for any engine oil leaks in the final step.

Engine oil exposure must be prevented when replacing the oil filter sub-assembly because prolonged contact leads to skin irritation and dermatitis and includes dangerous material contaminants. Wear protective clothing with gloves so you can wash your skin thoroughly either with soap and water or use waterless hand cleaner to remove any used engine oil while abstaining from using gasoline or thinners or solvents. The proper location to discard oil filters and.used oil products exists at specific disposal sites. First drain all engine oil before extracting the oil filter sub-assembly with Special Service Tool: 09228-06501. Before installation, inspect and clean the mounting area while applying fresh engine oil to the gasket inside a new oil filter before starting mounting and continuing to tighten it until the gasket meets the seat. Complete the filter installation using Special Service Tool: 09228-06501 by adding 3/4 more turns of torque. Replace the oil drain plug and use a new gasket before torquing the plug to 38 Nm (382 kgf-cm, 28 ft. lbs.). The oil fill should contain 3.7 liters (3.9 US qts, 3.3 Imp. qts) when using a new filter but only 3.4 liters (3.6 US qts, 3.0 Imp. qts) without replacement or 4.1 liters (4.3 US qts, 3.6 Imp. qts) as a dry fill capacity. The last step should involve a leak inspection of the engine oil.

The replacement of oil filter sub-assemblies requires coming in contact with engine oil for minimum time because extended exposure creates skin irritation and dermatitis while exposing the body to dangerous contaminants. Wear protective gear along with gloves and thoroughly clean your skin under water with soap or utilize waterless hand cleaning products when removing engine oil contents because gasoline and solvents remain forbidden. The proper locations exist for disposal of oil filters together with used engine oil. The process starts with draining engine oil followed by removing the sub-assembly of the oil filter by using Special Service Tool: 09228-06501. Before installing a new oil filter you should apply clean engine oil around its gasket surface along with cleaning the installation area thoroughly. Use Special Service Tool: 09228-06501 to partially tighten the oil filter until its gasket touches the seat, then continue tightening it with the tool by another 3/4 turn. The service requires installation of the oil pan drain plug together with a new gasket and torque to 38 Nm (382 kgf-cm, 28 ft. lbs.). Filling the engine requires 3.7 liters (3.9 US qts., 3.3 Imp. qts.) after replacing the oil filter but only 3.4 liters (3.6 US qts., 3.0 Imp. qts.) when retaining the filter, and complete the procedure with 4.1 liters (4.3 US qts., 3.6 Imp. qts.) for bare fill-ups. Engine oil leaks should be inspected at the conclude of the process.

The first step when replacing the 1NZ-FXE oil filter sub-assembly requires precautionary measures to protect from engine oil exposure that causes skin irritation and carries harmful contaminants. Protect your skin through wear of gloves and protective clothing followed by immediate skin washing when interacting with engine oil. Destroy used engine oil along with filters at official locations. Start by draining engine oil through the removal of the oil filler cap followed by the oil drain plug which leads to oil collecting in a container. Wipe down the drain plug and replace it with a fresh gasket then torque it to 38 Nm. Special Service Tool: 09228-06501 should be used during the process to remove the oil filter. To install the new oil filter you should clean the surface where it will go and apply engine oil to its gasket before screwing it lightly into its seat and using the same tool to secure it with a torque of 17.5 Nm (178 kgf-cm, 13 ft. lbs). The specified amount of fresh engine oil required for this service is 3.7 liters (3.9 US qts, 3.3 Imp. qts) for replacement including a new oil filter or 3.4 liters (3.6 US qts, 3.0 Imp. qts) without an oil filter change or 4.1 liters (4.3 US qts, 3.6 Imp. qts) for a dry fill operation and the oil filler cap must be installed last. Finally, inspect the engine oil.

Engaging in engine oil replacement requires protecting your skin from coming into contact with old oil since it is a cause of dryness and irritation. Use protective clothing together with gloves before washing your skin thoroughly when finished. The appropriate facilities must be utilized for the disposal of oil and filters that become used. Begin by unfastening the engine under cover on the right-hand side and then proceed to drain the engine oil by removing the oil filler cap and oil drain plug until the oil reaches a container. The oil drain plug should receive a new gasket before installation to achieve 37 Nm (377 kgf-cm, 27 ft. lbs.) torque value. The removal process for the oil filter sub-assembly starts using Special Service Tool: 09228-06501. The installation process begins by washing the oil filter seating area then smearing the new oil filter gasket with clean engine oil before easy screwing it in place but stopping when the gasket touches the seat. The oil filter requires a torque of 13 Nm (133 kgf-cm, 10 ft. lbs.) using Special Service Tool: 09228-06501 when there is space but can manually reach 3/4 turn if no space allows. Following engine oil addition install the oil filler cap before searching for any oil leaks and finally reattach the engine under cover RH.

The replacement of the oil filter requires care because skin dryness dermatitis and irritation from mineral oil exposure persists while used engine oil bears detrimental contaminants. Use protective gear combined with gloves while cleaning your skin with soap and water or a water-less hand cleaner to remove used engine oil particles - steer clear from gasoline as well as thinners or solvents. You should discard used oil as well as oil filters at specific authorized disposal locations. Begin the task by first removing the engine under cover from the right-hand side before draining engine oil by taking out the oil pan drain plug. Special Service Tool: 09228-06501 should be used to extract the oil filter sub-assembly. You should install new oil filters by cleaning their surface, adding oil to the filter gasket, placing it gently before tightening until the gasket makes contact with the seat. Proceed to install the special service tool: 09228-06501 to complete another 3/4 turn of the installation. The oil pan drain plug needs installation with its new gasket and torquing to 37 Nm of torque. Engineering specifications require the addition of 1.4 liters (4.7 US qts, 3.9 Imp. qts) when changing the oil filter and performing oil drain and refilling and 4.2 liters (4.4 US qts, 3.7 Imp. qts) when changing oil without replacing the filter while 4.8 liters (5.1 US qts, 4.2 Imp. qts) should be used for dry filling. Conduct a final examination for oil leakage.

Use proper protection during oil filter installation to prevent skin exposure to damaged motor oil since it can lead to drying and irritation and possibly raise skin cancer risks. Protect your skin using gloves and protective clothing which will prevent oil absorption and wash contaminated areas with either soap water or waterless hand cleaner whereas solvents and thinner must be strictly avoided. Proper oil disposal sites exist for environmental protection of used engine oil along with filters. The oil pan drain plug removal should precede oil draining procedures while cleaning the plug before installing a new gasket which requires 38 N m (382 kgf cm, 28 ft. lbf) torque. The second stage involves the removal of the oil filter sub-assembly through Special Service Tool: 09228-06501. The oil filter installation requires preparation of the surface followed by graining clean engine oil on the new filter gasket and slow tightening until it touches the seat. The oil filter requires tightening using Special Service Tool: 09228-06501 either through torque wrench at 13 N m (133 kgf cm, 9.5 ft. lbf) when space permits or through manual hand tightening with a common wrench for restricted areas. The procedure requires using fresh engine oil at the indicated oil capacity followed by leak inspection and examination of the oil level.

Use Special Service Tool: 09228-06501 to remove the oil filter.

Add 3.7 liters (3.9 US qts, 3.3 Imp. qts) with oil filter replacement, 3.4 liters (3.6 US qts, 3.0 Imp. qts) without, or 4.1 liters (4.3 US qts, 3.6 Imp. qts) for dry fill.

Clean and reinstall the oil drain plug with a new gasket, torquing it to 37 Nm (377 kgf-cm, 27 ft. lbs.).

For a drain and refill with oil filter change, use 3.7 liters (3.9 US qts, 3.3 Imp. qts); for a drain and refill without oil filter change, use 3.5 liters (3.7 US qts, 3.1 Imp. qts); and for a dry fill, use 4.2 liters (4.4 US qts, 3.7 Imp. qts).

Check and clean the oil filter installation surface, apply clean engine oil to the gasket of the new oil filter, lightly screw it into place, and tighten until the gasket contacts the seat.

Special Service Tool: 09228-06501.

Fill with fresh engine oil and check for any oil leakage.

Clean the drain plug and install it with a new gasket, tightening it to a torque of 37 Nm (377 kgf-cm, 27 ft-lbf).

Clean the drain plug and reinstall it with a new gasket, tightening it to a torque of 37 Nm (377 kgf-cm, 27 ft-lbf).

Check and clean the oil filter installation surface, apply clean engine oil to the gasket of a new oil filter, lightly screw it into place, and tighten until the gasket contacts the seat.

Use Special Service Tool: 09228-06501 to remove the oil filter sub-assembly.

Begin by draining the engine oil: remove the oil filler cap, then the oil drain plug, and drain the oil into a container.

Clean the drain plug and reinstall it with a new gasket, torqued to 38 Nm (387 kgf-cm, 28 ft-lbf).

Inspect for any oil leaks.

Use Special Service Tool: 09228-06501 to remove the oil filter.

Add fresh engine oil and reinstall the oil filler cap, ensuring to check the engine oil level afterward.

Fill with fresh engine oil and check for any oil leakage.

Drain the engine oil by removing the oil pan drain plug and allowing the oil to flow out completely.

Avoid skin contact with used engine oil, wear protective clothing and gloves, and dispose of used oil and filters at designated disposal sites.