How to remove the Knock Sensor on Toyota Tacoma?

You must disconnect the negative battery terminal cable as the first step when removing the Knock Sensor. After disconnecting the negative terminal cable you should proceed to remove the engine under cover sub-assembly that exists on 4WD and Pre-Runner vehicles. First drain engine coolant before removing the intake air connector. Secondly step is to take off the throttle with motor body assembly. Erase all connections from the fuel hose and fuel hose No.2. Unscrew the fuel vapor feed hose at the VSV along with the vacuum hose and clamp bracket bolt before the intake manifold can be taken off. The maintenance technician should first disconnect water by-pass hose No. 2 followed by ventilation hose No. 3 and VSV connector. The engine wire harness clamp and compressor magnetic clutch connector need to be separated when using air conditioning. Follow the illustration by removing the nut together with the bolt and harness clamp bracket then detach the three connectors. Apply sequence to disconnect the relay block first then release the intake manifold by removing five bolts along with two nuts. The knock control sensor removal process requires disconnecting its connector followed by removing the bolt until the sensor can be extracted.

OEM Toyota Tacoma Knock Sensor

Engine Knock Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Knock Sensors found

View related parts
Toyota Tacoma Knock Sensor
Part Number: 89615-12090
$145.22 MSRP: $205.57
You Save: $60.35 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Knock Control; Ignition Knock (Detonation) Sensor
- Manufacturer Note: DENSO
- Replaces: 89615-12050, 89615-32010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Sensor, Knock Control
Part Number: 89615-50010
$156.62 MSRP: $221.71
You Save: $65.09 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Ignition Knock (Detonation) Sensor; Knock Sensor
- Manufacturer Note: MATSUSHITA
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-1999 Toyota Tacoma | Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Knock Sensor
Part Number: 89615-26010
$149.33 MSRP: $211.39
You Save: $62.06 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Knock Control
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2000-2004 Toyota Tacoma | Base, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
Toyota Tacoma Knock Sensor
Part Number: 89615-12040
$175.77 MSRP: $248.82
You Save: $73.05 (30%)
ADD TO CART
Product Specifications
- Other Name: Sensor, Knock Control; Ignition Knock (Detonation) Sensor
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 1995-2004 Toyota Tacoma | Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
Toyota Tacoma Knock Sensor
Part Number: 89615-06010
$138.05 MSRP: $195.42
You Save: $57.37 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor, Knock Control; Ignition Knock (Detonation) Sensor
- Replaces: 89615-BZ030, 89615-20090, 89615-BZ040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2005-2023 Toyota Tacoma | Base, Limited, Pre Runner, SR, SR5, Trail, Trail Special Edition, TRD Off-Road, TRD Pro, TRD Sport, X-Runner | 4 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 4.0 L GAS

Toyota Tacoma Knock Sensor

If you're thinking about purchasing OEM parts for your Toyota Tacoma, our website is your one-stop destination. We stock an extensive selection of genuine Toyota Tacoma Knock Sensor at pocket-friendly prices. Plus, we guarantee a swift delivery and a hassle-free return policy for your convenience.

Toyota Tacoma Knock Sensor Parts Questions & Experts Answers

Knock Sensor
89615-06010
Q: How to remove the Knock Sensor on Toyota Tacoma?
A: You must disconnect the negative battery terminal cable as the first step when removing the Knock Sensor. After disconnecting the negative terminal cable you should proceed to remove the engine under cover sub-assembly that exists on 4WD and Pre-Runner vehicles. First drain engine coolant before removing the intake air connector. Secondly step is to take off the throttle with motor body assembly. Erase all connections from the fuel hose and fuel hose No.2. Unscrew the fuel vapor feed hose at the VSV along with the vacuum hose and clamp bracket bolt before the intake manifold can be taken off. The maintenance technician should first disconnect water by-pass hose No. 2 followed by ventilation hose No. 3 and VSV connector. The engine wire harness clamp and compressor magnetic clutch connector need to be separated when using air conditioning. Follow the illustration by removing the nut together with the bolt and harness clamp bracket then detach the three connectors. Apply sequence to disconnect the relay block first then release the intake manifold by removing five bolts along with two nuts. The knock control sensor removal process requires disconnecting its connector followed by removing the bolt until the sensor can be extracted.