Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2020-2023 Toyota Corolla | Hybrid LE, Hybrid SE, Hybrid XLE, L, LE, SE, SE Nightshade, XLE, XSE | 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
Manufacturer Note: 3-SPOKE,LEATHER,AUDIO-JBL-AM/FM CD CHANGER 8SPEAKER BLUETOOTH,DK.GRAY,TRIM1#,TYPE B:REFER ILLUST.
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
Fits the following Vehicles:
2009-2013 Toyota Corolla | S | 4 Cyl 1.8 L GAS
| Page 1 of 4 |Next >
1-20 of 72 Results
Toyota Corolla Steering Wheel
Choose genuine Steering Wheel that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Steering Wheel for your Toyota Corolla? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Corolla parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.
Q: How to remove the steering wheel on Toyota Corolla?
A:
The first step to remove the steering wheel involves turning front wheels parallel to the vehicle path then disconnecting the cable from the negative terminal while allowing a minimum of 90 seconds before resetting the SRS system. The technician should first remove the steering pad followed by the lower No. 2 then lower No. 3 steering wheel covers before continuing. Start the steering wheel removal process by unscrewing the set nut before marking the alignment between parts and detaching spiral cable connectors. Apply a small amount of grease to threads along with the tip of Special Service Tool (09953-05020) before utilization during this process. Special Service Tools 09950-50013, 09951-05010, 09952-05010, 09953-05020, and 09954-05021 are required for this procedure. First remove the steering pad switch LH if equipped from the system and then take off the No. 1 steering wheel ornament by unmounting the screw and unlocking 2 pins. Proceed to remove the steering pad switch assembly when the system has built-in microphone functionality followed by removing the cruise control main switch if installed. To complete the process remove the lower steering wheel boss cover by first unscrewing the two screws and then releasing the two claws before removing the two attachment screws associated with the lower steering wheel boss cover.
Q: How to install the steering wheel on Toyota Corolla?
A:
You must start steering wheel installation through attaching the 2 steering wheel pad attaching screws to the lower steering wheel boss cover. The 2 claws should be used to connect the lower steering wheel boss cover with the steering wheel sub-assembly before adding the two screws. The cruise control main switch should be installed when a system is present. Place the steering pad switch LH when installing this feature on the model. Secure the 2 pins to fasten the No. 1 steering wheel ornament onto the steering wheel sub-assembly before installing the screw. The vehicle requires a steering pad switch assembly which needs installation. Adjust the spiral cable only when the front wheels are precisely pointing forward. Line up the matchmarks between the steering wheel assembly and steering main shaft before inserting the steering wheel assembly set nut to 50 Nm (510 kgf-cm, 37 ft-lbf). Then, connect the connectors to the spiral cable sub-assembly. Add the steering pad next to installing both the lower No. 3 and lower No. 2 steering wheel covers. The steering wheel center point requires examination followed by connecting the cable to the negative battery terminal and testing the steering pad function. The SRS warning light must be inspected as the last step.