How to replace the Front No. 1 Car Speakers Assy on Scion xA?

The procedure to swap the Front No. 1 Speaker Assy starts by taking off the Front Door Lower Frame Bracket Garnish LH followed by the Power Window Regulator Master Switch Assy and then the Front Door Trim Board Sub-Assy LH. After connector detachment from the Front No. 1 Speaker Assy use a drill with less than 4 mm (0.16 in.) diameter to drill 3 rivet heads and separate the speaker from the front door panel while rotating the drill near the rivet head to cut flanges. Avoiding both the damage to rivet holes and drill bit breakage. Take precautions because the severed rivet will be warm so proceed with drilling until you remove all debris pieces. The procedure requires vacuum cleaning of the drilled rivet along with the interior front door panel dust. When installing the Front No. 1 Speaker Assy on the front door panel you should use an air riveter or hand riveter to add three new strike rivets according to the provided order illustration. The riveter requires operator care to prevent damage by not prizing it and by keeping it level to rivet at correct alignment. You must not break the tightened rivets from materials once they become securely fastened. Drop the rivet into place only when the materials have no space between them before reattaching the connector.

OEM Scion xA Car Speakers

Audio Speakers

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Car Speakers found

View related parts
Scion xA Door Speaker, Rear
Part Number: 86160-33620
$112.43 MSRP: $152.96
You Save: $40.53 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Center, Front, Rear; Quarter Panel Speaker; Front Driver Speaker; Rear Driver Speaker; Speaker Assembly, Front; Speaker Assembly, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2006 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Tweeter, Driver Side
Part Number: 86160-52260
$83.36 MSRP: $113.42
You Save: $30.06 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Left; Speaker Assembly, Front
- Manufacturer Note: LH
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Tweeter, Passenger Side
Part Number: 86160-52250
$83.27 MSRP: $113.29
You Save: $30.02 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Right; Speaker Assembly, Front
- Manufacturer Note: RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Tweeter, Passenger Side
Part Number: 86160-52120
$83.35 MSRP: $113.40
You Save: $30.05 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Right; Speaker Assembly, Front
- Manufacturer Note: RH
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2005 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Rear Driver Speaker
Part Number: 86160-2B570
$149.93 MSRP: $205.71
You Save: $55.78 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Rear; Speaker Assembly, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2005 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Quarter Panel Speaker, Rear
Part Number: 86160-13080
$108.88 MSRP: $148.12
You Save: $39.24 (27%)
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Rear; Rear Driver Speaker; Speaker Assembly, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2006 Scion xA | Base | 4 Cyl 1.5 L GAS
View related parts
Scion xA Tweeter, Driver Side
Part Number: 86160-52130
Product Specifications
- Other Name: Speaker Assembly, Radio; Speaker, Left; Speaker Assembly, Front
- Manufacturer Note: LH
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2004-2005 Scion xA | Base | 4 Cyl 1.5 L GAS

Scion xA Car Speakers

If you're thinking about purchasing OEM parts for your Scion xA, our website is your one-stop destination. We stock an extensive selection of genuine Scion xA Car Speakers at pocket-friendly prices. Plus, we guarantee a swift delivery and a hassle-free return policy for your convenience.

Scion xA Car Speakers Parts Questions & Experts Answers

Tweeter, Passenger Side
86160-52120
Q: How to replace the Front No. 1 Car Speakers Assy on Scion xA?
A: The procedure to swap the Front No. 1 Speaker Assy starts by taking off the Front Door Lower Frame Bracket Garnish LH followed by the Power Window Regulator Master Switch Assy and then the Front Door Trim Board Sub-Assy LH. After connector detachment from the Front No. 1 Speaker Assy use a drill with less than 4 mm (0.16 in.) diameter to drill 3 rivet heads and separate the speaker from the front door panel while rotating the drill near the rivet head to cut flanges. Avoiding both the damage to rivet holes and drill bit breakage. Take precautions because the severed rivet will be warm so proceed with drilling until you remove all debris pieces. The procedure requires vacuum cleaning of the drilled rivet along with the interior front door panel dust. When installing the Front No. 1 Speaker Assy on the front door panel you should use an air riveter or hand riveter to add three new strike rivets according to the provided order illustration. The riveter requires operator care to prevent damage by not prizing it and by keeping it level to rivet at correct alignment. You must not break the tightened rivets from materials once they become securely fastened. Drop the rivet into place only when the materials have no space between them before reattaching the connector.