How to install the hood cable assembly on 2009 Toyota Highlander?

The hood cable assembly installation requires passing it through the engine compartment into the upper radiator support followed by connecting the clamps according to the illustrations while attaching the cable to the hood lock control lever. Secure the hood lock assembly containing no engine hood courtesy switch by tightening three bolts to 8.0 Nm (82 kgf-cm, 71 in-lbf). Then fit the hood lock nut cap after applying MP grease to the hood lock sliding regions. When installing the assembly that contains the engine hood courtesy switch maintain the same approach from the beginning but wire the connector after completing assembly installation. After inspecting and necessary adjustments of the hood sub-assembly the team will install the radiator grille along with cool air intake duct seal and front fender liner LH then they will install the front fender moulding sub-assembly LH and subsequently the No.1 engine under cover followed by adjusting the engine under cover assembly for 2GR-FE.

OEM 2009 Toyota Highlander Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Hood Cables found

View related parts
2009 Toyota Highlander Release Cable, Front
Part Number: 53630-0E040
$35.73 MSRP: $49.74
You Save: $14.01 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-48050
- Part Name Code: 53630
- Item Weight: 0.80 Pounds
- Item Dimensions: 13.7 x 10.7 x 1.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53630-0E040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Highlander Lever Sub-Assembly, Hood Lock Control, Front
Part Number: 53611-0E010-C0
$14.67 MSRP: $20.43
You Save: $5.76 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control
- Manufacturer Note: BLACK,TRIM2#
- Position: Front
- Replaces: 53611-22010-C0, 53611-22010-B7, 53611-02030-C0, 53611-22010-B1
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.3 x 11.1 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-C0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Highlander Release Lever, Sand, Front
Part Number: 53611-0E010-E0
$13.17 MSRP: $18.33
You Save: $5.16 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: SAND BEIGE,TRIM4#
- Position: Front
- Replaces: 53611-22010-E5
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.1 x 11.0 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-E0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2009 Toyota Highlander Release Lever, Sand, Front
Part Number: 53611-0E010-B1
$13.19 MSRP: $18.36
You Save: $5.17 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: GRAY,TRIM1#
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.4 x 11.2 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-B1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2009 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS

2009 Toyota Highlander Hood Cable

Looking for affordable OEM 2009 Toyota Highlander Hood Cable? Explore our comprehensive catalogue of genuine 2009 Toyota Highlander Hood Cable. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2009 Toyota Highlander Parts Questions & Experts Answers

Q: How to install the hood cable assembly on 2009 Toyota Highlander?
A: The hood cable assembly installation requires passing it through the engine compartment into the upper radiator support followed by connecting the clamps according to the illustrations while attaching the cable to the hood lock control lever. Secure the hood lock assembly containing no engine hood courtesy switch by tightening three bolts to 8.0 Nm (82 kgf-cm, 71 in-lbf). Then fit the hood lock nut cap after applying MP grease to the hood lock sliding regions. When installing the assembly that contains the engine hood courtesy switch maintain the same approach from the beginning but wire the connector after completing assembly installation. After inspecting and necessary adjustments of the hood sub-assembly the team will install the radiator grille along with cool air intake duct seal and front fender liner LH then they will install the front fender moulding sub-assembly LH and subsequently the No.1 engine under cover followed by adjusting the engine under cover assembly for 2GR-FE.