How to remove the Hood Cable on 2008 Toyota Highlander?

The Hood Cable needs to be removed after Engine Under Cover Assembly together with No. 1 Engine Under Cover. The service technician should begin by removing the Front Fender Moulding Sub-Assembly LH and then the Front Fender Liner LH. As the next step remove both the Cool Air Intake Duct Seal and the Radiator Grille. You should start by removing the hood lock nut cap before proceeding to eliminate three bolts and detach the hood lock control cable while also removing the assembly for the Hood Lock Assembly without Engine Hood Courtesy Switch. Garage owners must disconnect the connector from Hood Lock Assemblies with Engine Hood Courtesy Switches then remove the hood lock nut cap and three bolts before disconnecting the hood lock control cable to extract the assembly. Lastly for Hood Lock Control Cable Assembly removal you need to disconnect the cable from the hood lock control lever then disconnect the clamps with a screwdriver whose tip you need to tape beforehand before pulling the cable from the engine compartment.

OEM 2008 Toyota Highlander Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Hood Cables found

View related parts
2008 Toyota Highlander Release Cable, Front
Part Number: 53630-0E040
$35.73 MSRP: $49.74
You Save: $14.01 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly, Hood Lock; Hood Release Cable, Front; Cable Assembly, Hood Lock Control; Hood Release Cable
- Position: Front
- Replaces: 53630-48050
- Part Name Code: 53630
- Item Weight: 0.80 Pounds
- Item Dimensions: 13.7 x 10.7 x 1.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53630-0E040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Lever Sub-Assembly, Hood Lock Control, Front
Part Number: 53611-0E010-C0
$14.67 MSRP: $20.43
You Save: $5.76 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control
- Manufacturer Note: BLACK,TRIM2#
- Position: Front
- Replaces: 53611-22010-C0, 53611-22010-B7, 53611-02030-C0, 53611-22010-B1
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.3 x 11.1 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-C0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Release Lever, Sand, Front
Part Number: 53611-0E010-E0
$13.17 MSRP: $18.33
You Save: $5.16 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: SAND BEIGE,TRIM4#
- Position: Front
- Replaces: 53611-22010-E5
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.1 x 11.0 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-E0
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS
View related parts
2008 Toyota Highlander Release Lever, Sand, Front
Part Number: 53611-0E010-B1
$13.19 MSRP: $18.36
You Save: $5.17 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Lever, Hood Lock Control; Hood Release Handle, Front; Lever Sub-Assembly, Hood Lock Control
- Manufacturer Note: GRAY,TRIM1#
- Position: Front
- Part Name Code: 53601
- Item Weight: 0.70 Pounds
- Item Dimensions: 13.4 x 11.2 x 1.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 53611-0E010-B1
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2008 Toyota Highlander Submodels:
- Base, Hybrid, Hybrid Limited, Limited, Plus, SE, Sport | 4 Cyl 2.7 L GAS, 6 Cyl 3.3 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS

2008 Toyota Highlander Hood Cable

Looking for affordable OEM 2008 Toyota Highlander Hood Cable? Explore our comprehensive catalogue of genuine 2008 Toyota Highlander Hood Cable. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2008 Toyota Highlander Parts Questions & Experts Answers

Q: How to remove the Hood Cable on 2008 Toyota Highlander?
A: The Hood Cable needs to be removed after Engine Under Cover Assembly together with No. 1 Engine Under Cover. The service technician should begin by removing the Front Fender Moulding Sub-Assembly LH and then the Front Fender Liner LH. As the next step remove both the Cool Air Intake Duct Seal and the Radiator Grille. You should start by removing the hood lock nut cap before proceeding to eliminate three bolts and detach the hood lock control cable while also removing the assembly for the Hood Lock Assembly without Engine Hood Courtesy Switch. Garage owners must disconnect the connector from Hood Lock Assemblies with Engine Hood Courtesy Switches then remove the hood lock nut cap and three bolts before disconnecting the hood lock control cable to extract the assembly. Lastly for Hood Lock Control Cable Assembly removal you need to disconnect the cable from the hood lock control lever then disconnect the clamps with a screwdriver whose tip you need to tape beforehand before pulling the cable from the engine compartment.