Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Center Right Outer; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Position: Outer Passenger Side
Part Name Code: 73360
Item Weight: 2.20 Pounds
Item Dimensions: 12.0 x 10.8 x 8.2 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-35310-B0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2003 Toyota 4Runner Submodels:
Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Center Right Outer; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Passenger Side
Manufacturer Note: FAWN,TRIM4#
Position: Outer Passenger Side
Part Name Code: 73360
Item Weight: 2.30 Pounds
Item Dimensions: 12.1 x 11.0 x 8.4 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73360-35310-E0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2003 Toyota 4Runner Submodels:
Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
Other Name: Belt Assembly, Rear Seat; Seat Belt Lap and Shoulder Belt, Center Left Outer; Belt & Retractor; Belt Assembly, Rear Seat 3 Point Type, Outer Driver Side
Manufacturer Note: FAWN,TRIM4#
Position: Outer Driver Side
Part Name Code: 73370
Item Weight: 3.30 Pounds
Item Dimensions: 11.3 x 6.3 x 5.1 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73370-35240-E0
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2003 Toyota 4Runner Submodels:
Limited, Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
Other Name: Belt Assembly, Front Seat; Seat Belt Receptacle, Front Right; Latch; Belt Assembly, Front Seat Inner, Passenger Side
Manufacturer Note: DK.GRAY,TRIM13
Position: Passenger Side
Part Name Code: 73230
Item Weight: 1.50 Pounds
Item Dimensions: 14.2 x 11.2 x 2.3 inches
Condition: New
Fitment Type: Direct Replacement
SKU: 73230-35840-B1
Warranty: This genuine part is guaranteed by Toyota's
factory warranty.
More Info
Fits the following 2003 Toyota 4Runner Submodels:
Sport, SR5 | 6 Cyl 4.0 L GAS, 8 Cyl 4.7 L GAS
| Page 1 of 2 |Next >
1-20 of 32 Results
2003 Toyota 4Runner Seat Belt
Looking for affordable OEM 2003 Toyota 4Runner Seat Belt? Explore our comprehensive catalogue of genuine 2003 Toyota 4Runner Seat Belt. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!
2003 Toyota 4Runner Seat Belt Parts Q&A
Q: What is the proper procedure for installing a new seat belt tongue plate stopper and inspecting the seat belt assembly for damage on 2003 Toyota 4Runner?
A: The new service part of the seat belt tongue plate stopper is introduced with additional installation instructions to support repair procedures. Start by placing the tongue plate at the upper end of its stopper then secure it there by using tape or a clip. You should use pliers to remove all fragments from the original tongue plate stopper that remain present in the webbing. All occupants face potential injuries from seat belt breakdown in accidents so the manufacturer requires seat belt assembly replacement when webbing exhibits cutting, fraying, wear, damage, or following severe impacts. Check all parts of the webbing for damage before repairing the assembly by replacing it with care taken to avoid webbing harm during installation. First position the new tongue plate stopper into the webbing hole with the proper orientation in mind. Adjust the tongue plate stopper inside the webbing using an adjustable wrench before using hand pressure to align both male and female areas parallel to each other while turning the adjustment screw. Staying away from using pliers proves essential since they tend to create damages in the webbing material. Use adjustable joint pliers to tighten the adjustable wrench adjustment screw until its jaws create 4.5 - 5.0 mm (0.18 in. - 0.20 in.) of space when hand-turning is no longer possible. The last check involves examining how the male pin of the tongue plate stopper is even deformed within the female part and securely fastened onto the belt webbing.