How to Service and Repair the Drive Shaft on 2000 Toyota Tacoma?

The first step for drive/propeller shaft service and repair on models RZN191L-TRPDKAB, RZN196L-CRPDKAB, VZN195L-CRPDKAB starts with front 4WD propeller shaft removal through matchmarking the propeller shaft and front differential flanges followed by torquing 4 nuts, bolts, and washers to 74 Nm (750 kgf-cm, 54 ft. lbs.). Begin by suspending the front side of the propeller shaft then marking both the propeller shaft and transfer flanges before removing 4 nuts and washers with identical torque value. When handling the pre-runner and rear propeller shaft (4WD) start by applying matchmarks to the flanges of transmission (pre-runner) and transfer (4WD). Proceed to remove 4 nuts and washers with 74 Nm (750 kgf-cm, 54 ft. lbs.) torque. After that, apply matchmarks to the propeller shaft rear differential flanges before uninstalling all flange hardware with the same torque specifications. To remove the propeller shaft from the 3-joint type system the installer should detach both bearing plates and support bolts from the frame crossmember while following a torque sequence of 36 Nm (370 kgf-cm, 27 ft. lbs.). Deformation of the propeller shaft tube will occur if you grip it tightly in a vise during disassembly. Before detachment begin by matchmarking the flanges and unfasten the four nuts along with their bolts and washers to separate the shafts. Special Service Tool: 09330-00021 and a chisel and hammer enable the removal of the intermediate shaft flange after unstaking its nut. Then apply Special Service Tool: 09950-30011 (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020) to remove the flange and spacer components. When inspecting the center support bearing check its free movement before replacing it in cases of damage or wear. Runout measurements on propeller shafts and intermediate shafts can be done using a dial indicator to detect damage. The standard maximum acceptable runout value is 0.8 mm (0.031 inch) for both shafts. If runout exceeds this limit then replacement of the shafts is needed. Check the spider bearings for possible damage and wear since maximum axial play must stay below 0.05 mm (0.0020 inch). Plan to replace any components that fail to meet these criteria. When inspecting the double cardan joint propeller shaft for wear and damage it must be replaced when any problems appear. Install the center support bearing and spacer to the intermediate shaft using the cutout at the rear opening while applying MP grease to the intermediate shaft splines. Then use Special Service Tool: 09330-00021 to secure the flange and spacer and nut with torques set to 181 Nm (1,850 kgf-cm, 134 ft. lbs.) then 69 Nm (700 kgf-cm, 51 ft. lbs.) before staking the nut. The installation of the propeller shaft alongside the intermediate shaft requires alignment of their matchmarks followed by securing them with four bolts, washers, and nuts which must be torqued to 74 Nm (750 kgf-cm, 54 ft. lbs.). The sleeve yoke installation requires applying grease to both spline and sliding surfaces of the propeller shaft and this allows proper insertion and dust cover application. When the vehicle is unloaded the installation process should align the center bearing center line with the housing center line into a 0 plus or minus 1 mm (0 plus or minus 0.04 inch) range from the car's front and rear direction while maintaining housing center line perpendicular to the front propeller shaft axis. The oil seals require lithium base chassis grease Type NLGI No. 2 for spiders together with molybdenum disulfide lithium base chassis grease of NLGI No. 2 serving as the lubricant for sleeve yoke and double cardan joint.

OEM 2000 Toyota Tacoma Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Drive Shafts found

View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D260
$1391.61 MSRP: $2039.42
You Save: $647.81 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-3D150
- Part Name Code: 37100
- Item Weight: 43.20 Pounds
- Item Dimensions: 59.3 x 11.9 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D260
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D030
$648.12 MSRP: $949.83
You Save: $301.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 43.60 Pounds
- Item Dimensions: 58.1 x 12.2 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35170
$439.37 MSRP: $643.90
You Save: $204.53 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 16.10 Pounds
- Item Dimensions: 30.3 x 5.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35170
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37110-04040
$392.13 MSRP: $574.68
You Save: $182.55 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Manufacturer Note: DANA
- Replaces: 37110-3D200
- Part Name Code: 37110
- Item Weight: 14.60 Pounds
- Item Dimensions: 34.4 x 6.8 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35180
$393.04 MSRP: $576.01
You Save: $182.97 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.30 Pounds
- Item Dimensions: 29.5 x 5.3 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35180
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-60300
$397.92 MSRP: $583.15
You Save: $185.23 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 16.70 Pounds
- Item Dimensions: 30.6 x 5.4 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-60300
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft, Front
Part Number: 37140-35160
$397.92 MSRP: $583.15
You Save: $185.23 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.20 Pounds
- Item Dimensions: 30.3 x 5.5 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-35160
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D240
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-35790
- Part Name Code: 37100
- Item Weight: 40.40 Pounds
- Item Dimensions: 58.1 x 12.2 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D240
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D250
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-3D140
- Part Name Code: 37100
- Item Weight: 41.20 Pounds
- Item Dimensions: 59.9 x 12.1 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D250
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37110-35880
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-3D220
- Part Name Code: 37110
- Item Weight: 41.60 Pounds
- Item Dimensions: 59.9 x 11.7 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-35880
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37110-35790
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Part Name Code: 37110
- Item Weight: 44.00 Pounds
- Item Dimensions: 57.6 x 12.1 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-35790
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37110-35780
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37110-3D180
- Part Name Code: 37110
- Item Weight: 40.80 Pounds
- Item Dimensions: 58.7 x 12.3 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-35780
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-35820
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 40.80 Pounds
- Item Dimensions: 58.7 x 12.1 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-35820
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Pre Runner, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-35830
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 15.30 Pounds
- Item Dimensions: 34.0 x 6.8 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-35830
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D040
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 15.70 Pounds
- Item Dimensions: 34.4 x 6.9 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5 | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D230
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Manufacturer Note: TYPE B:REFER TO ILLUSTRATION
- Replaces: 37100-35750
- Part Name Code: 37100
- Item Weight: 42.80 Pounds
- Item Dimensions: 75.9 x 8.2 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D230
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS, 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37100-3D220
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Replaces: 37100-35740
- Part Name Code: 37100
- Item Weight: 45.90 Pounds
- Item Dimensions: 74.9 x 9.3 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-3D220
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, Limited, Pre Runner, SR5, S-Runner | 6 Cyl 3.4 L GAS
View related parts
2000 Toyota Tacoma Drive Shaft
Part Number: 37110-04050
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Manufacturer Note: DANA
- Replaces: 37110-3D210
- Part Name Code: 37110
- Item Weight: 15.10 Pounds
- Item Dimensions: 33.4 x 6.9 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37110-04050
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota Tacoma Submodels:
- Base, DLX, SR5 | 4 Cyl 2.4 L GAS, 4 Cyl 2.7 L GAS

2000 Toyota Tacoma Drive Shaft

Looking for affordable OEM 2000 Toyota Tacoma Drive Shaft? Explore our comprehensive catalogue of genuine 2000 Toyota Tacoma Drive Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2000 Toyota Tacoma Drive Shaft Parts Q&A

Q: How to Service and Repair the Drive Shaft on 2000 Toyota Tacoma?
A: The first step for drive/propeller shaft service and repair on models RZN191L-TRPDKAB, RZN196L-CRPDKAB, VZN195L-CRPDKAB starts with front 4WD propeller shaft removal through matchmarking the propeller shaft and front differential flanges followed by torquing 4 nuts, bolts, and washers to 74 Nm (750 kgf-cm, 54 ft. lbs.). Begin by suspending the front side of the propeller shaft then marking both the propeller shaft and transfer flanges before removing 4 nuts and washers with identical torque value. When handling the pre-runner and rear propeller shaft (4WD) start by applying matchmarks to the flanges of transmission (pre-runner) and transfer (4WD). Proceed to remove 4 nuts and washers with 74 Nm (750 kgf-cm, 54 ft. lbs.) torque. After that, apply matchmarks to the propeller shaft rear differential flanges before uninstalling all flange hardware with the same torque specifications. To remove the propeller shaft from the 3-joint type system the installer should detach both bearing plates and support bolts from the frame crossmember while following a torque sequence of 36 Nm (370 kgf-cm, 27 ft. lbs.). Deformation of the propeller shaft tube will occur if you grip it tightly in a vise during disassembly. Before detachment begin by matchmarking the flanges and unfasten the four nuts along with their bolts and washers to separate the shafts. Special Service Tool: 09330-00021 and a chisel and hammer enable the removal of the intermediate shaft flange after unstaking its nut. Then apply Special Service Tool: 09950-30011 (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020) to remove the flange and spacer components. When inspecting the center support bearing check its free movement before replacing it in cases of damage or wear. Runout measurements on propeller shafts and intermediate shafts can be done using a dial indicator to detect damage. The standard maximum acceptable runout value is 0.8 mm (0.031 inch) for both shafts. If runout exceeds this limit then replacement of the shafts is needed. Check the spider bearings for possible damage and wear since maximum axial play must stay below 0.05 mm (0.0020 inch). Plan to replace any components that fail to meet these criteria. When inspecting the double cardan joint propeller shaft for wear and damage it must be replaced when any problems appear. Install the center support bearing and spacer to the intermediate shaft using the cutout at the rear opening while applying MP grease to the intermediate shaft splines. Then use Special Service Tool: 09330-00021 to secure the flange and spacer and nut with torques set to 181 Nm (1,850 kgf-cm, 134 ft. lbs.) then 69 Nm (700 kgf-cm, 51 ft. lbs.) before staking the nut. The installation of the propeller shaft alongside the intermediate shaft requires alignment of their matchmarks followed by securing them with four bolts, washers, and nuts which must be torqued to 74 Nm (750 kgf-cm, 54 ft. lbs.). The sleeve yoke installation requires applying grease to both spline and sliding surfaces of the propeller shaft and this allows proper insertion and dust cover application. When the vehicle is unloaded the installation process should align the center bearing center line with the housing center line into a 0 plus or minus 1 mm (0 plus or minus 0.04 inch) range from the car's front and rear direction while maintaining housing center line perpendicular to the front propeller shaft axis. The oil seals require lithium base chassis grease Type NLGI No. 2 for spiders together with molybdenum disulfide lithium base chassis grease of NLGI No. 2 serving as the lubricant for sleeve yoke and double cardan joint.

Related 2000 Toyota Tacoma Parts

Alternate Year Models

1999 Toyota Tacoma Drive Shaft 2001 Toyota Tacoma Drive Shaft