My Garage
Cart

OEM 2000 Toyota RAV4 Sway Bar Kit

Stabilizer Sway Bar Set
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Sway Bar Kits found

  • 2000 Toyota RAV4 Sway Bar Kit - 48811-42021
    2000 Toyota RAV4 Sway Bar Kit Diagram - 48811-42021
    View related parts
    Product Specifications
    • Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
    • Manufacturer Note: W(235/60R16 TIRE)
    • Position: Front
    • Replaces: 48811-42020
    • Part Name Code: 48811
    • Item Weight: 7.90 Pounds
    • Item Dimensions: 42.9 x 11.9 x 4.9 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 48811-42021
    • Warranty: This genuine part is guaranteed by Toyota's factory warranty.
    More Info
    Fits the following 2000 Toyota RAV4 Submodels:
    • Base | 4 Cyl 2.0 L GAS
  • 2000 Toyota RAV4 Sway Bar Kit - 48811-42011
    2000 Toyota RAV4 Sway Bar Kit Diagram - 48811-42011
    View related parts
    Product Specifications
    • Other Name: Bar, Stabilizer, Front; Suspension Stabilizer Bar, Front; Sway Bar
    • Position: Front
    • Replaces: 48811-42010
    • Part Name Code: 48811
    • Item Weight: 7.70 Pounds
    • Item Dimensions: 42.5 x 12.3 x 5.0 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • SKU: 48811-42011
    • Warranty: This genuine part is guaranteed by Toyota's factory warranty.
    More Info
    Fits the following 2000 Toyota RAV4 Submodels:
    • Base | 4 Cyl 2.0 L GAS

2000 Toyota RAV4 Sway Bar Kit

Looking for affordable OEM 2000 Toyota RAV4 Sway Bar Kit? Explore our comprehensive catalogue of genuine 2000 Toyota RAV4 Sway Bar Kit. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2000 Toyota RAV4 Parts Questions & Experts Answers

  • Q: How to service and repair the Sway Bar Kit on 2000 Toyota RAV4?
    A: Start the sway bar kit service by taking out the front wheels while tightening them to 103 Nm (1,050 kgf-cm, 76 ft. lbs.). A torque of 44 Nm (450 kgf-cm, 33 ft. lbs.) must be applied to these four nuts when servicing the links of sway bar kits in 2 Door vehicles and 4 Door vehicles and all over fender vehicles but if the ball joint rotates with the nut use a 5 mm hexagon wrench to stabilize the stud. You should remove the sway bar kit through the steps of unbolting 4 small parts along with 2 brackets and removing the No.1 bushings using a torque of 29 Nm (300 kgf-cm, 22 ft. lbs.). It is essential to position the No.1 bushing outside the paint line while ensuring the bushing cutout points toward the vehicle's rear. Remove the sway bar kit from the right-hand side before you can access the two bushings by taking out both clamps using a screwdriver to extract the 2 cushions. During sway bar link inspection workers must rotate the ball joint stud 5 times in each direction prior to nut installation. Workers must apply torque using a wrench by giving the nut constant single rotations at a rate of 3 - 5 seconds for the 5th turn. Turning torque measurements must fall within 0.05 - 1.0 Nm (0.5 - 10 kgf-cm, 0.4 - 8.7 inch lbs.) for 2 Door vehicles and 0.05 - 2.0 Nm (0.5 - 20 kgf-cm, 0.4 The process of installation follows the exact opposite sequence as removal steps.

Related 2000 Toyota RAV4 Parts