How to service and repair the Brake Master Cylinder on Toyota Sequoia?

Begin service and repair on the Brake Master Cylinder with reservoir removal following set screw extraction and reservoir pull out and completing the operation with 1.5 Nm torque (15 kgf-cm, 13 inch lbs.). After strainer and cap removal from the reservoir position the technician should remove 2 grommets, the seal, and 2 master cylinder pressure sensors using 25 Nm (250 kgf-cm, 18 ft. lbs.) torque. Inspection of the cylinder requires compressed air cleaning then checking for wear and damage followed by cleaning or replacing the cylinder assembly. The assembly process requires the reverse order of disassembly steps while greasing the marked rubber parts with lithium soap base glycol grease.

How to remove and replace the brake master cylinder on Toyota Sequoia?

The braking process starts by lowering the brake fluid before immediately cleaning off any fluid that reaches paint surfaces. Separate the brake fluid level warning switch connector after disconnecting the front No. 1 brake tube (marked as A) and the rear No. 1 brake tube (marked as B) from the brake master cylinder through use of a union nut wrench. Fluishing the brake pedal multiple times to release the booster vacuum pressure inside the unit requires removing two nuts securing the brake master cylinder to the brake booster and extracting its attached brake master cylinder seal.

OEM Toyota Sequoia Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Brake Master Cylinders found

View related parts
Toyota Sequoia Master Cylinder
Part Number: 47201-0C071
$206.31 MSRP: $294.56
You Save: $88.25 (30%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Replaces: 47201-0C070
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2008-2022 Toyota Sequoia | Limited, Nightshade, Platinum, SR5, TRD Pro, TRD Sport | 8 Cyl 4.6 L GAS, 8 Cyl 4.7 L GAS, 8 Cyl 5.7 L FLEX, 8 Cyl 5.7 L GAS
View related parts
Toyota Sequoia Master Cylinder
Part Number: 47201-0C041
$478.05 MSRP: $700.59
You Save: $222.54 (32%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Replaces: 47201-0C040
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001-2007 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
Toyota Sequoia Master Cylinder
Part Number: 47055-0C030
$924.90 MSRP: $1355.45
You Save: $430.55 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Booster Assembly, W/Master Cylinder
- Manufacturer Note: *614
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2023-2024 Toyota Sequoia | Capstone, Limited, Platinum, SR5, TRD Pro | 6 Cyl 3.4 L FULL HYBRID EV-GAS (FHEV)
View related parts
Toyota Sequoia Master Cylinder
Part Number: 47201-0C012
Product Specifications
- Other Name: Cylinder Sub-Assembly, Brake Stroke Simulator; Brake Master Cylinder; Brake Reservoir; Cylinder Sub-Assembly, Brake Master
- Manufacturer Note: W/O(VSC)
- Replaces: 47201-0C011, 47201-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
Fits the following Vehicles:
- 2001 Toyota Sequoia | Limited, SR5 | 8 Cyl 4.7 L GAS

Toyota Sequoia Brake Master Cylinder

Choose genuine Brake Master Cylinder that pass strict quality control tests. You can trust the top quality and lasting durability. Shopping for OEM Brake Master Cylinder for your Toyota Sequoia? Our website is your one-stop destination. We stock an extensive selection of genuine Toyota Sequoia parts. The price is affordable so you can save more. It only takes minutes to browse and find the exact fit. Easily add to cart and check out fast. Our hassle-free return policy will keep you stress-free. We process orders quickly for swift delivery. Your parts will arrive faster, so you can get back on the road sooner.

The Brake Master Cylinder in Toyota Sequoia automobiles is one of the aesthetic parts of braking mechanism which translates the foot pressure of the driver into hydraulic pressure. This hydraulic pressure is transmitted through slave cylinders and makes the brakes apply force and hence provide the friction required to halt the vehicle. The master cylinder often has built-in pistons with seals and springs and may be made of cast iron or aluminum; the fluid reserves can be embedded into the master cylinder or located apart. Sequoia models use dual circuit master cylinders and this means that if one housing fails, the other one has enough force to operate the brakes. This design renders HBAH safe given that the car can still stop even in case of hydraulic failure. In the course of usage of the car brake system, the Brake Master Cylinder is not exempted from experiencing some problems like leakage of the fluid, or a failure of internalfunctions which can ultimately affect the brakes efficiency. It is highly recommended to inspect the Brake Master Cylinder frequently, so that the car's condition and safety of the Toyota Sequoia would not be compromised.

Toyota Sequoia Brake Master Cylinder Parts and Q&A

Master Cylinder
47201-0C041
Q: How to service and repair the Brake Master Cylinder on Toyota Sequoia?
A:
Begin service and repair on the Brake Master Cylinder with reservoir removal following set screw extraction and reservoir pull out and completing the operation with 1.5 Nm torque (15 kgf-cm, 13 inch lbs.). After strainer and cap removal from the reservoir position the technician should remove 2 grommets, the seal, and 2 master cylinder pressure sensors using 25 Nm (250 kgf-cm, 18 ft. lbs.) torque. Inspection of the cylinder requires compressed air cleaning then checking for wear and damage followed by cleaning or replacing the cylinder assembly. The assembly process requires the reverse order of disassembly steps while greasing the marked rubber parts with lithium soap base glycol grease.
Master Cylinder
47201-0C071
Q: How to remove and replace the brake master cylinder on Toyota Sequoia?
A:
The braking process starts by lowering the brake fluid before immediately cleaning off any fluid that reaches paint surfaces. Separate the brake fluid level warning switch connector after disconnecting the front No. 1 brake tube (marked as A) and the rear No. 1 brake tube (marked as B) from the brake master cylinder through use of a union nut wrench. Fluishing the brake pedal multiple times to release the booster vacuum pressure inside the unit requires removing two nuts securing the brake master cylinder to the Brake Booster and extracting its attached brake master cylinder seal.