How to service and repair the drive shaft on 2003 Toyota Tundra?

Start drive/propeller shaft maintenance by taking apart propeller shaft and intermediate shaft components and marking the propeller shaft and yoke before separating the center yoke during disassembly sequence. You should begin by removing the center support bearing from the intermediate shaft through a hammer chisel operation on the nut stake followed by the vise clamp of the yoke to extract the spacer and nut then creating matchmarks on both components. A combination of brass bar and hammer allows professionals to extract the center yoke as well as spacer and center support bearing from the intermediate shaft. Use a dial indicator to measure propeller shaft and intermediate shaft runout and damage; replace the shaft when runout reaches or exceeds 0.8 mm (0.031 inch) maximum limit. To check the spider bearing you must measure its maximum allowable 0.05 mm (0.0020 inch) axial play with a dial indicator while firmly holding the shaft. A free-moving center support bearing signals proper condition but requires immediate replacement in case of damage. To reinstall the center support bearing on the intermediate shaft use its proper direction and apply MP grease to the splines of the shaft before installing the spacer and center yoke by lining up matchmarks. Direction alignment must be maintained when installing new intermediate shaft front side yoke and center yoke so their faces point in the same direction. Attaching the vise around the yoke enables you to push the bearing into place using a new nut tightened to 181 Nm (1,845 kgf-cm, 133 ft. lbs.). The nut must be subsequently loosened then retorqued to 82 Nm (835 kgf-cm, 60 ft. lbs.) before final staking with a hammer and punch. When finishing the assembly sequence connect the propeller shaft with the intermediate shaft through the center yoke.

OEM 2003 Toyota Tundra Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Drive Shafts found

View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-34051
$1228.51 MSRP: $1800.41
You Save: $571.90 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-34050
- Item Weight: 78.80 Pounds
- Item Dimensions: 93.5 x 10.5 x 10.6 inches
- Condition: New
- SKU: 37100-34051
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2003 Toyota Tundra Drive Shaft, Front
Part Number: 37140-0C020
$347.43 MSRP: $496.05
You Save: $148.62 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.30 Pounds
- Item Dimensions: 33.4 x 6.8 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-0C020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-0C020
$746.71 MSRP: $1094.30
You Save: $347.59 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 15.70 Pounds
- Item Dimensions: 34.7 x 6.9 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-0C020
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-34101
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-34100
- Item Weight: 15.10 Pounds
- Item Dimensions: 34.4 x 6.9 x 5.5 inches
- Condition: New
- SKU: 37100-34101
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-34061
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft
- Replaces: 37100-34060
- Item Weight: 14.90 Pounds
- Item Dimensions: 34.7 x 6.7 x 5.6 inches
- Condition: New
- SKU: 37100-34061
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft, Front
Part Number: 37140-0C030
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.10 Pounds
- Item Dimensions: 33.4 x 6.9 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-0C030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-0C030
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Part Name Code: 37100
- Item Weight: 15.00 Pounds
- Item Dimensions: 34.0 x 6.8 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-0C030
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Base, SR5 | 6 Cyl 3.4 L GAS
View related parts
2003 Toyota Tundra Drive Shaft
Part Number: 37100-0C010
$830.92 MSRP: $1217.73
You Save: $386.81 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller W/Center Bearing
- Replaces: 37120-0C010
- Part Name Code: 37100
- Item Weight: 15.40 Pounds
- Item Dimensions: 34.0 x 6.8 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37100-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS
View related parts
2003 Toyota Tundra Drive Shaft, Front
Part Number: 37140-0C010
$395.88 MSRP: $580.16
You Save: $184.28 (32%)
Product Specifications
- Other Name: Shaft Assembly, Propeller; Driveshaft; Shaft Assembly, Propeller, Front
- Position: Front
- Part Name Code: 37140
- Item Weight: 15.00 Pounds
- Item Dimensions: 35.0 x 7.0 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 37140-0C010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2003 Toyota Tundra Submodels:
- Limited, SR5 | 8 Cyl 4.7 L GAS

2003 Toyota Tundra Drive Shaft

Looking for affordable OEM 2003 Toyota Tundra Drive Shaft? Explore our comprehensive catalogue of genuine 2003 Toyota Tundra Drive Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2003 Toyota Tundra Parts Questions & Experts Answers

Q: How to service and repair the drive shaft on 2003 Toyota Tundra?
A: Start drive/propeller shaft maintenance by taking apart propeller shaft and intermediate shaft components and marking the propeller shaft and yoke before separating the center yoke during disassembly sequence. You should begin by removing the center support bearing from the intermediate shaft through a hammer chisel operation on the nut stake followed by the vise clamp of the yoke to extract the spacer and nut then creating matchmarks on both components. A combination of brass bar and hammer allows professionals to extract the center yoke as well as spacer and center support bearing from the intermediate shaft. Use a dial indicator to measure propeller shaft and intermediate shaft runout and damage; replace the shaft when runout reaches or exceeds 0.8 mm (0.031 inch) maximum limit. To check the spider bearing you must measure its maximum allowable 0.05 mm (0.0020 inch) axial play with a dial indicator while firmly holding the shaft. A free-moving center support bearing signals proper condition but requires immediate replacement in case of damage. To reinstall the center support bearing on the intermediate shaft use its proper direction and apply MP grease to the splines of the shaft before installing the spacer and center yoke by lining up matchmarks. Direction alignment must be maintained when installing new intermediate shaft front side yoke and center yoke so their faces point in the same direction. Attaching the vise around the yoke enables you to push the bearing into place using a new nut tightened to 181 Nm (1,845 kgf-cm, 133 ft. lbs.). The nut must be subsequently loosened then retorqued to 82 Nm (835 kgf-cm, 60 ft. lbs.) before final staking with a hammer and punch. When finishing the assembly sequence connect the propeller shaft with the intermediate shaft through the center yoke.

Related 2003 Toyota Tundra Parts

Alternate Year Models

2002 Toyota Tundra Drive Shaft 2004 Toyota Tundra Drive Shaft