How to service and repair the axle shaft on 2000 Toyota RAV4?

Commence axle shaft repair procedures by examining the drive shaft for leg movement at its outboard section while verifying both inboard section smooth motion along thrust axis and minimal resistance to radial force and inspecting the boot condition. You should cut the outboard clamps before uninstalling inboard and outboard joint boot clamps using a screwdriver for these inboard clamps. First apply matchmarks to either the inboard tulip or center drive shaft or drive shaft. Then detach the snap ring along with removing the tulip. The disassembly of the inboard joint follows these steps: Drive shaft and cage receive match marks while snap ring and inner race get their own designations before balls and cage are removed. A snap ring expander extracts the snap ring whereas a brass bar extracts the inner race. Cease joint boot and clamp removal from both inboard and outboard areas without breaking apart the outboard assembly. Use a press to eliminate the dust cover on the right-hand side whereas the left-hand side requires Special Service Tool: 09950-00020 and a press for removal. Use the same tool to remove the bearing and after that remove the snap ring and end the sequence by taking out the No.2 dust deflector using a screwdriver while hammering it in place. 2WD A/T and 4WD owners need to conduct drive shaft examinations followed by boot clamp uninstallation then add match marks to the inboard joint tulip. A snap ring expander working together with a brass bar should be used to safely remove the tripod while protecting the outboard joint integrity. A new No.2 dust deflector can be installed using Special Service Tools: 09309-36010, 09316-20011 and a press for the subsequent assembly of a center drive shaft for 2WD RH through straight pin, new bearing, snap ring, and bearing case assembly installation with various special service tools. The dust cover must be installed while checking that all specifications match. Position new outboard and inboard joint boots on the transmission units but protect the spline by wrapping vinyl tape around them. Place the tripod with its beveled edge aimed at the outboard joint while matching its marks precisely before expanding the new snap ring with the aid of snap ring tools. Start by applying grease to the outboard joint along with its boot then reinstall following the correct placement of matchmarks while setting the boot temporarily in place. Then apply the same procedure to the inboard joint tulip or center drive shaft by setting matchmarks correctly and temporarily installing the boot. The boot clamp assembly process should finish with boot clamp tightening using a screwdriver while maintaining correct boot positioning and avoiding both stretching and contracting.

OEM 2000 Toyota RAV4 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

22 Axle Shafts found

View related parts
2000 Toyota RAV4 Axle Assembly, Rear Driver Side
Part Number: 42340-42012
$387.49 MSRP: $567.87
You Save: $180.38 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear Left; Axle Shaft
- Position: Rear Driver Side
- Replaces: 42340-42011
- Item Weight: 15.20 Pounds
- Item Dimensions: 27.9 x 8.3 x 7.4 inches
- Condition: New
- SKU: 42340-42012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Rear Passenger Side
Part Number: 42330-42012
$387.57 MSRP: $567.98
You Save: $180.41 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear Right; Axle Shaft
- Position: Rear Passenger Side
- Replaces: 42330-42011
- Item Weight: 16.20 Pounds
- Item Dimensions: 27.6 x 8.7 x 7.7 inches
- Condition: New
- SKU: 42330-42012
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Passenger Side
Part Number: 43410-20583
$451.70 MSRP: $661.97
You Save: $210.27 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle, Front Right; Joint Kit; GSP Cv Axle; Axle Shaft
- Position: Front Passenger Side
- Replaces: 43410-20582, 43410-20581
- Item Weight: 5.90 Pounds
- Item Dimensions: 8.0 x 4.3 x 4.3 inches
- Condition: New
- SKU: 43410-20583
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Passenger Side
Part Number: 43410-20543
$449.78 MSRP: $659.15
You Save: $209.37 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Passenger Side
- Replaces: 43410-20542, 43410-20541
- Item Weight: 14.50 Pounds
- Item Dimensions: 30.1 x 7.4 x 6.5 inches
- Condition: New
- SKU: 43410-20543
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Outer Joint Assembly, Front
Part Number: 43470-49018
$195.29 MSRP: $278.84
You Save: $83.55 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Joint
- Position: Front
- Replaces: 43470-49017, 43470-49016
- Item Weight: 14.00 Pounds
- Item Dimensions: 30.8 x 6.3 x 5.5 inches
- Condition: New
- SKU: 43470-49018
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Outer Joint Assembly, Driver Side
Part Number: 43470-29239
$207.08 MSRP: $295.67
You Save: $88.59 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Outboard; CV Joint
- Position: Driver Side
- Replaces: 43470-29228, 43470-29230, 43470-29229
- Item Weight: 12.90 Pounds
- Item Dimensions: 30.8 x 6.2 x 5.4 inches
- Condition: New
- SKU: 43470-29239
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Shafts, Driver Side
Part Number: 42380-49016
$235.80 MSRP: $336.67
You Save: $100.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; Axle Shaft; CV Joint; Outer Joint; Shaft Assembly, Rear Drive Outboard Joint, Driver Side
- Position: Driver Side
- Part Name Code: 42380
- Item Weight: 14.20 Pounds
- Item Dimensions: 34.0 x 6.4 x 5.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42380-49016
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
2000 Toyota RAV4 Axle Shafts, Driver Side
Part Number: 42380-49026
$235.80 MSRP: $336.67
You Save: $100.87 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; Axle Shaft; CV Joint; Outer Joint; Shaft Assembly, Rear Drive Outboard Joint, Driver Side
- Manufacturer Note: W(ABS)
- Position: Driver Side
- Part Name Code: 42380
- Item Weight: 13.80 Pounds
- Item Dimensions: 33.3 x 6.2 x 5.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42380-49026
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
2000 Toyota RAV4 Axle Shafts, Passenger Side
Part Number: 42370-49026
$249.11 MSRP: $355.68
You Save: $106.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; Axle Shaft; CV Joint; Outer Joint; Shaft Assembly, Rear Drive Outboard Joint, Passenger Side
- Manufacturer Note: W(ABS)
- Position: Passenger Side
- Part Name Code: 42370A
- Item Weight: 14.50 Pounds
- Item Dimensions: 33.3 x 6.5 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42370-49026
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS, BATTERY EV (EV/BEV)
View related parts
2000 Toyota RAV4 Axle Assembly, Driver Side
Part Number: 43420-42041
$397.98 MSRP: $583.24
You Save: $185.26 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; GSP Cv Axle; Axle Shaft; Shaft Assembly, Front Drive, Driver Side; CV Axle Assembly
- Manufacturer Note: W(ABS)
- Position: Driver Side
- Replaces: 43420-42031
- Part Name Code: 43420
- Item Weight: 15.10 Pounds
- Item Dimensions: 28.9 x 7.2 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 43420-42041
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Driver Side
Part Number: 43420-42023
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: 43420-42022, 43420-42021
- Item Weight: 14.20 Pounds
- Item Dimensions: 30.4 x 5.1 x 5.2 inches
- Condition: New
- SKU: 43420-42023
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Passenger Side
Part Number: 43410-42013
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Passenger Side
- Replaces: 43410-42012, 43410-42011
- Item Weight: 5.80 Pounds
- Item Dimensions: 8.1 x 4.2 x 4.2 inches
- Condition: New
- SKU: 43410-42013
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Driver Side
Part Number: 43420-42013
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: 43420-42011, 43420-42012
- Item Weight: 15.30 Pounds
- Item Dimensions: 30.1 x 7.2 x 6.6 inches
- Condition: New
- SKU: 43420-42013
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Outer Joint Assembly, Passenger Side
Part Number: 43470-19659
Product Specifications
- Other Name: Shaft Assembly, Outboard; CV Joint
- Position: Passenger Side
- Replaces: 43470-19658, 43470-19648, 43470-19647, 43470-19646, 43470-19645, 43470-19656
- Item Weight: 5.70 Pounds
- Item Dimensions: 8.1 x 4.2 x 4.3 inches
- Condition: New
- SKU: 43470-19659
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Hub, Rear
Part Number: 42301-42010
Product Specifications
- Other Name: Shaft Sub-Assembly, Rear Axle; Wheel Hub, Rear; Wheel Hub Repair Kit; Shaft, Rear Axle, Passenger Side; Shaft, Rear Axle, Driver Side; Wheel Hub
- Position: Rear
- Item Weight: 16.40 Pounds
- Item Dimensions: 27.9 x 8.7 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 42301-42010
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Rear Passenger Side
Part Number: 42330-42022
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear Right; Axle Shaft
- Position: Rear Passenger Side
- Replaces: 42330-42021
- Item Weight: 15.80 Pounds
- Item Dimensions: 27.9 x 8.5 x 7.7 inches
- Condition: New
- SKU: 42330-42022
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Rear Driver Side
Part Number: 42340-42022
Product Specifications
- Other Name: Shaft Assembly, Rear Drive; CV Axle Assembly, Rear Left; Axle Shaft
- Position: Rear Driver Side
- Replaces: 42340-42021
- Item Weight: 16.40 Pounds
- Item Dimensions: 28.2 x 8.5 x 7.7 inches
- Condition: New
- SKU: 42340-42022
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Driver Side
Part Number: 43420-20294
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: 43420-20293, 43420-20292
- Item Weight: 14.20 Pounds
- Item Dimensions: 30.4 x 7.3 x 6.5 inches
- Condition: New
- SKU: 43420-20294
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Driver Side
Part Number: 43420-20304
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Left; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Driver Side
- Replaces: 43420-20302, 43420-20303
- Item Weight: 6.00 Pounds
- Item Dimensions: 8.1 x 4.3 x 4.1 inches
- Condition: New
- SKU: 43420-20304
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS
View related parts
2000 Toyota RAV4 Axle Assembly, Front Passenger Side
Part Number: 43410-42023
Product Specifications
- Other Name: Shaft Assembly, Front Drive; CV Axle Assembly, Front Right; Joint Kit, Drive Shaft; CV Axle Assembly; Axle Shaft
- Position: Front Passenger Side
- Replaces: 43410-42021, 43410-42022
- Item Weight: 14.90 Pounds
- Item Dimensions: 29.8 x 5.2 x 5.2 inches
- Condition: New
- SKU: 43410-42023
- Warranty: This genuine part is guaranteed by Toyota's factory warranty.
More Info
Fits the following 2000 Toyota RAV4 Submodels:
- Base | 4 Cyl 2.0 L GAS

| Page 1 of 2 |Next >

1-20 of 22 Results

2000 Toyota RAV4 Axle Shaft

Looking for affordable OEM 2000 Toyota RAV4 Axle Shaft? Explore our comprehensive catalogue of genuine 2000 Toyota RAV4 Axle Shaft. All our parts are covered by the manufacturer's warranty. Plus, our straightforward return policy and speedy delivery service ensure an unparalleled shopping experience. We look forward to your visit!

2000 Toyota RAV4 Parts Questions & Experts Answers

Q: How to service and repair the axle shaft on 2000 Toyota RAV4?
A: Commence axle shaft repair procedures by examining the drive shaft for leg movement at its outboard section while verifying both inboard section smooth motion along thrust axis and minimal resistance to radial force and inspecting the boot condition. You should cut the outboard clamps before uninstalling inboard and outboard joint boot clamps using a screwdriver for these inboard clamps. First apply matchmarks to either the inboard tulip or center drive shaft or drive shaft. Then detach the snap ring along with removing the tulip. The disassembly of the inboard joint follows these steps: Drive shaft and cage receive match marks while snap ring and inner race get their own designations before balls and cage are removed. A snap ring expander extracts the snap ring whereas a brass bar extracts the inner race. Cease joint boot and clamp removal from both inboard and outboard areas without breaking apart the outboard assembly. Use a press to eliminate the dust cover on the right-hand side whereas the left-hand side requires Special Service Tool: 09950-00020 and a press for removal. Use the same tool to remove the bearing and after that remove the snap ring and end the sequence by taking out the No.2 dust deflector using a screwdriver while hammering it in place. 2WD A/T and 4WD owners need to conduct drive shaft examinations followed by boot clamp uninstallation then add match marks to the inboard joint tulip. A snap ring expander working together with a brass bar should be used to safely remove the tripod while protecting the outboard joint integrity. A new No.2 dust deflector can be installed using Special Service Tools: 09309-36010, 09316-20011 and a press for the subsequent assembly of a center drive shaft for 2WD RH through straight pin, new bearing, snap ring, and bearing case assembly installation with various special service tools. The dust cover must be installed while checking that all specifications match. Position new outboard and inboard joint boots on the transmission units but protect the spline by wrapping vinyl tape around them. Place the tripod with its beveled edge aimed at the outboard joint while matching its marks precisely before expanding the new snap ring with the aid of snap ring tools. Start by applying grease to the outboard joint along with its boot then reinstall following the correct placement of matchmarks while setting the boot temporarily in place. Then apply the same procedure to the inboard joint tulip or center drive shaft by setting matchmarks correctly and temporarily installing the boot. The boot clamp assembly process should finish with boot clamp tightening using a screwdriver while maintaining correct boot positioning and avoiding both stretching and contracting.

Related 2000 Toyota RAV4 Parts

Alternate Year Models

1999 Toyota RAV4 Axle Shaft 2001 Toyota RAV4 Axle Shaft